- ページ 27

楽器 Yamaha DM2000VCMのPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。Yamaha DM2000VCM 28 ページ。 Yamaha acoustic guitar-accessory: owners manual
Yamaha DM2000VCM にも：オーナーズマニュアル (1 ページ)

ページを印刷する

DM2000V2 Short-Cut List

Using the 'SEL' switches

1. CHANNEL PAIR

Hold [SEL] for one channel and press [SEL] for the adjacent channel to make a stereo pair. This works for input and output

channels, so long as the left side is an odd number and the right side is an even number. The channel with the [SEL] button

you hold ﬁrst is the master channel for the pair: its settings are copied to the other channel (except for pan and bus routing

settings). Repeating this action breaks the stereo pair, to make the channels mono again.

2. CHANNEL NAME DISPLAY

To view the long name for a channel, press and hold its [SEL] button for more than a second. The name will be displayed in

the ﬂuorescent window above the faders.

3. CHANNEL COPY

Select the source channel with its [SEL] button, then press the [CHANNEL COPY] button (in the SELECTED CHANNEL

area). Then press the [SEL] button of the destination channel and press [PASTE].

NOTE:

The parameters which are copied are determined on the PREFERENCES 2 page in the SETUP menu.

Other Short-Cuts

1. EQ Gain to 0dB

To reset the gain of an EQ band to 0dB, press and hold the [FREQUENCY/Q] encoder for one second.

2. EQ Reset

To return the whole Parametric EQ for a channel to its default settings, press the [FREQUENCY/Q] encoders for the LOW

and HIGH bands at the same time.

3. AUX ON/OFF

To access the AUX ON/OFF buttons quickly, press and hold the required [AUX# SELECT] button. Then the [ON] buttons

above the faders become the AUX ON buttons for the selected Aux.

TIP:

This can be useful for creating a MIX-MINUS. First set an AUX to ALL NOMINAL, using the button at the top of the SEND1-

24 page in the AUX DISPLAY menu, then hold the AUX SELECT button to switch off the send for the required 'minus' channel.

4. AUX SOLO

To solo an AUX MASTER while still viewing an INPUT FADER LAYER, press the required [AUX# SELECT] button once to

select it, and once again to SOLO it. Pressing a third time will cancel the SOLO. While the AUX is in SOLO, its SELECT but-

ton will ﬂash.

NOTE:

This function can be disabled in the SOLO page of the MONITOR menu, with the AUX/SOLO LINK option.

5. Copy STEREO Mix to an AUX

Press and hold an INPUT FADER LAYER button, then press an [AUX# SELECT] button, and click YES in the conﬁrmation

box on the LCD. This copies the fader levels to the selected AUX sends. Make sure the Aux sends are all PRE by clicking the

[GLOBAL PRE] button on the SEND1-24 page in the AUX DISPLAY menu.

NOTE:

Repeat the same procedure for each fader layer to copy the whole mix to the Aux sends, as only one layer is copied at a time.

TIP:

This is useful for making a quick headphone mix in a recording session (where AUX 11 and 12 can be sent directly to the STU-

DIO MONITOR OUT), or making a quick stage-monitor mix for a guest musician at a live performance.

6. GEQ edit on Faders

In the GEQ EDIT page (EFFECTS/PLUG-INS menu), click one of the [FADER ASSIGN] buttons to access the GEQ bands

on the faders. When you navigate away from this page, the faders return to their normal mode, but the cursor position is

remembered, so next time the GEQ EDIT page is accessed, you only need to press [ENTER] to get fader control.

7. SCENE FADE TIME Copy

To assign the same fade time to all channels in a scene, ﬁrst enter the required FADE TIME for one channel, then double-

click [ENTER] to copy the time to all the other input or output channels.

27/28

DM2000V2 Quick Start Guide