- ページ 11

照明器具 ALUZ A8-ZIZA-TAPEのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。ALUZ A8-ZIZA-TAPE 11 ページ。 Led tape
ALUZ A8-ZIZA-TAPE にも：マニュアル (14 ページ)

ページを印刷する

ZIZA

Tape

A8-ZIZA-TAPE

TROUBLESHOOTING TIPS

• Do not reset the breaker multiple times

• If the unit is overloaded, the breaker will trip, shutting off the transformer and lights

• If the breaker reset button has been held down by hand or any type of pressure,

such as duct tape, or if the breaker has been reset multiple times without

troubleshooting, the unit will:

- Burn the transformer bobbin

- Burn the thermal or magnetic breaker

- Burn the primary or secondary wires due to high amperage caused by overload

- Short circuit in line which will not allow the breaker to reset

- Damage the lighting

Turn off power before beginning. Check for any twisting or damage to the

circuit in the LED lightstrip. If there is excessive damage and the circuit is

broken, the lightstrip must be replaced.

Torn Lightstrip

Check for metal particles or other foreign objects causing the short.

Foreign Object

Check to make sure cuts in the lightstrip are clean and not frayed, causing

positive and negative copper pads to touch.

CONTINUITY TEST

A continuity test is performed to determine if electricity can pass through two

points on an electrical circuit. This helps identify shorts or malfunctions in the line

or ﬁ xture. Use a multimeter or continuity tester to perform the steps below.

• Always perform a continuity test before connecting lighting to power source.

• Malfunctions are not always as obvious as the lights not turning on.

• A short or malfunction in the line or ﬁ xture will cause damage over time,

ultimately damaging the lighting and voiding warranty.

Turn power off before beginning. Verify power is turned off by using a

non-contact circuit tester. Touch the probe of the tester to positive wire of

the power source. The tester will light up if an electrical current is detected.

Setup your tester. First insert the black probe lead into the COM jack, then

insert the red probe lead into the VΩ jack.

Damaged Lightstrip

Metal Flakes

Frayed End

ALUZ

1170 North Red Gum Street, Anaheim, CA 92806

Phone: 800 921 2254 or 714 535 7900 | Fax: 714 535 7902 | [email protected] | aluz.lighting

Verify that your tester is functional by touching probes together. The tester

should light up, beep, or read 0Ω (ohms) of resistance.

Touch the red probe to the black wire and the black probe to each colored

wire. If a conductive path is formed between the black wire and any other

wire, the multimeter will beep, flash, or read 0Ω (ohms). Troubleshoot

to identify the malfunction in the line. If there is no conductive path, the

multimeter will not show any feedback.

Red Probe

Black

Black Probe

Touch the red probe to the ﬁ xture extrusion and the black probe to the

black wire. If a conductive path is formed between the extrusion and the

black wire, the multimeter will beep, flash, or read 0Ω (ohms). Troubleshoot

to identify the malfunction in the line. If there is no conductive path, the

multimeter will not show any feedback.

Black

Black Probe

Touch the red probe to the ﬁ xture extrusion and the black probe to the

each colored wire. If a conductive path is formed between the extrusion

and any colored wire, the multimeter will beep, flash, or read 0Ω (ohms).

Troubleshoot to identify the malfunction in the line. If there is no

conductive path, the multimeter will not show any feedback.

Black Probe

Set voltmeter to DC voltage and test power source. Conﬁ rm the correct

voltage before connecting lighting to power source. If voltage reading is

more than 1 volt higher than the marked output voltage, there is a problem

with the power source or driver.

Connect power connector to power source. If LEDs do not turn on, flip polarity

(+ -) or power source connection to power connector.

Black Probe

(-)

(+)

Red Probe

Installation Instructions

9 / 1 / 2021 / Rev 0

Page 11 of 11

Troubleshooting

RGBW Lighting

Red Probe

RGBW Lighting

Red Probe

RGBW Lighting