- ページ 7

食器洗い機 Asko D3731のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Asko D3731 16 ページ。 User manual d3731 use & care guide fr
Asko D3731 にも：取扱説明書 (16 ページ), (スペイン語) 操作とケア (16 ページ), (フランス語) 使用マニュアル (16 ページ)

ページを印刷する

Drying

This lets you select how long the turbo fan runs after

the final rinse. You have three options: Short, Economy

or Normal drying. ( Note : This option is not available

with the Pots & Pans and Rinse and Hold programs.)

To set the drying time, press Menu until "Drying"

displays, then press Set until your preference displays.

Express

This option reduces the wash time and lowers the wash

temperature by 20° F. ( Note : This option is not available

with the Quick Wash, Pots & Pans and Rinse and Hold

programs.) Press Menu until Express displays, then

press Set once to select On or twice to select Off. Press

Menu to confirm your selection.

Super rinse

The Super rinse option adds two extra rinses. This

gives an even better rinsing result. The Super rinse

option can be used in all programs except the Quick

wash and Rinse and Hold programs. Press Menu until

Super rinse displays, then press Set once to select On

or twice to select Off. Press Menu to confirm your

selection.

Cool Touch

This option lets you set a cool-down cycle after the drying

program (in all programs except Rinse and Hold). Press

Menu until Cool Touch displays, then press Set once to

select On or twice to select Off. Press Menu to confirm

your selection.

POWER BUTTON

Use this button to turn the main power to the unit on

and off. The location of the power button is illustrated

on page 6.

T/ST

OP BUTT

STAR

ART/ST

T/ST

T/STOP BUTT

OP BUTT

OP BUTTON

Once you have selected the wash program and options,

press this button to start the dishwasher. (Make sure

the door is securely closed.)

F F F F F A A A A A UL

T CODES

ULT CODES

T CODES

In the event that the machine should fail during a

program, the display window will show a fault code. The

table below defines these codes and gives possible

causes and solutions. See also "Troubleshooting" on

page 13.

Display

Overfilling

Water Inlet Fault

Inlet Valve Leakage

Water Outlet Fault

Blocked Filter

Type of Fault and Recommended Action

Too much water has entered the dishwasher. Call a service technician.

Water inlet fault. Make sure the water supply is open.

Valve leakage. Shut off the water supply and contact a service technician.

The drain is blocked. See "Troubleshooting" on page 12.

The filter is clogged. See "Cleaning the Filters" on page 9.

PROGRAM TIMES

The program times may not always be the same

because of variations in the household hot water

temperature. The dishwasher heats the water to the

proper temperature for the program selected; so if the

temperature of the water entering the dishwasher is too

low, the dishwasher will run longer because it takes

longer to heat the water. Raising your water heater

setting could help to shorten the cycle times.

INTERR

INTERRUPTING

INTERR

UPTING

UPTING A PR

INTERR

UPTING

TO ADD AN ITEM

If you want to interrupt a program to add an item, open

the door slightly until the spray arms stop turning. You

can then open the door fully and place the item into the

dishwasher. Close the door securely. The program will

continue from where it was interrupted.

WARNING! Be extremely careful when opening the

door during a program. The water is hot and you

could get scalded.

CHANGING OR STOPPING A

PROGRAM

OGRAM

If you decide to change the program after you have started

the machine, press the Start/

seconds. You will have to select the program and options

again when you are ready to restart the program. ( Note:

If the program has already gone through the wash cycle,

you will have to add detergent.).

If you have corrected the fault, turn the main power off

then back on to remove the fault indication. If it still

displays, try again to correct the problem or call a service

technician.

A PROGRAM

A PR

OGRAM

A PR

OGRAM

button for three

Stop

Page 7