AMEC TB-520 사용자 설명서 - 페이지 2

{카테고리_이름} AMEC TB-520에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. AMEC TB-520 2 페이지. Ais man overboard beacon

페이지 인쇄

Note:

When activated, the high beam LED on device will ash SOS signal in Morse code

format every minute.

Upon activation the device will transmit MOB ACTIVE signal every minute with

Lat/Lon position information. In case the GPS location cannot be updated due to

weather conditions, the last obtained Lat/Log GPS position will be sent.

As AIS MOB is still new on the market, not all chart plotters with AIS show the

correct

icon as recommended by the IMO. As a minimum, they will show the

same icon as used for other craft - normally an

for AIS MOB begins always with 972 which will di erentiate AIS MOB from

normal AIS targets. Please contact with your plotter manufacturer how they

display

on screen when there are further questions.

When the device is mounted in lifejacket, ensure the TB-520 remains out of the

water, as water will inhibit the GPS receiver and may cause di culties obtaining

GPS coordinates.

Ensure that the blue area marked "GPS Area" is not shielded or covered in any

way and always has a clear view of the sky. It is recommended that the Short Test

is performed monthly. Return the TB-520 to a service centre for battery

replacement if battery level is low.

Con rm that the battery expiry date shown is in date for the duration of

intended use.

This product emits low levels of radio frequency energy during operation. Avoid

handling the antenna once activated.

6.1 Battery Life Test

Start the battery life test by using the magnet found on

the back side of the test tab to touch the Test Area for one

full second.

The high beam LED will ash once and the beeper will beep

once signifying the device has entered into battery life test

mode. The green ash indicates that the battery is ok. If

your device ashes red light, this indicates low battery

power and the battery needs to be replaced. The device will

ash 3 times and beep once again to end the test.

6.2 Full Function Test

As illustrated, start the full function test by using the

magnet found on the back side of the test tab to touch the

Test Area. Just like the Battery Test, the strobe LED will ash

once and the device will beep once when the test magnet

approaches the Test Area. Hold the magnet next to the Test

Area for 3 additional seconds in which a second audible

beep indicates the unit is in Full Function Test. The battery

LED and GPS LED will commence to ash every 3 seconds

to indicate the battery status and GPS locating status:

7. Speci cation

APPLICABLE STANDARDS

IEC 60945

EN 303098- 1 V1.2.1

IEC 61108-1

EN 303098- 2 V1.2.1

GPS PERFORMANCE

Receiving Channels

Frequency

L1, 1575.42 MHz

Tracking Sensitivity

(-)159 dBm

Reacquisition

(-)159 dBm

Position Accuracy

＜ 2.0 m SBAS

＜ 2.5 m Autonomous

VHF PERFORMANCE

Frequency

Data Rate

Tx Power

Bandwidth

Modulation

Range

AIS Message Type

BATTERY

Type

Operating Time

Storage (battery life)

ACTIVATION METHOD

Manual activating or automatic activating with water sensor by immersion

Note: Speci cations are subject to change without prior notice.

. The MMSI number dedicated

- 5 -

- 7 -

ENVIRONMENTAL

Operating Temperature

-20°C~55°C

Storage Temperature

-30°C~70°C

Waterproof

IP68

Immersion Depth (optional)

50m

Compass Safe Distance

0.8m

Explosion Proof (optional)

Ex e m II T6 X

GENERAL/PHYSICAL

Model No.

TB-520

Size

129x52x40mm (L*W*D)

Weight

160 g (main unit only)

AIS 1, 161.975MHz

AIS 2, 162.025 MHz

9,600bps

2W (1W EIRP)

25 KHz

GMSK

4nm typical with receiver antenna > 5m above sea level

Message 1 (UID, GPS position, SOG, COG)

Message 14 (MOB ACTIVE or MOB TEST)

Primary Lithium (not rechargeable)

48 hours at -10°C, typical

5 years, replacement due after emergency use

- 9 -

5. Turning o your TB-520

Insert the activation tab back in the unit and the transmission will be ceased.

When the unit is activated by water sensor, pull the activation tab o and then

reinsert the tab subsequently to turn o the transmission. Put the antenna back

to its original position by wrapping around

the unit, as well as, the antenna cap.

5.1 Closing the red antenna cap

Align the red antenna cap with the unit, longer side facing the front and the

shorter side facing the back. Push the red antenna cap all the way until the

antenna cap clip pass the wedge. The proper tting of the red antenna cap

ensures the water sensors are properly seal from the elements and thus prevent

the unit from being activated when wet.

S/N(UNIQUE ID):

972160001

BATTERY EXPIRY:

JUL 2015

6. Testing your TB-520

The device is equipped with self test capability to perform 2 di erent tests to

ensure the beacon is working perfectly. The rst is a battery life test to check

the beacon's battery power. The second test is a GPS self test that includes

GPS activation and live test message transmission.

The green battery LED indicates that the battery is ok. If the

battery LED ashes red light, this indicates low battery power

and the battery needs to be replaced.

The green GPS LED next to the antenna indicates that GPS x is

achieved, the red GPS LED means that no GPS position is

obtained.

As soon as GPS x is achieved, the device will start sending MOB test messages,

which will be displayed with a

icon on all AIS systems within range. The Full

Function Test will be completed with a beep, after 8 bursts of test messages are

successfully sent. When no valid GPS data is obtained within 5 minutes, the Full

Function Test is regarded as failed and will be ended with a beep as well.

In case of a failed Full Function Test, check and make sure that the antenna is

pointing towards the sky and the "GPS Area" marked on the device is not

obstructed by hand or other objects. When the Full Function Test fails a second

time, return the device to your service center.

Note:

1) You can interrupt the test mode any time by pull o the activation tab and then

insert the tab subsequently. Please notice that under test mode, the device will

not transmit distress message also when the activation tab is removed. Hence

there is no risk of activating the alarm transmission when the user pulls the

activation tab o to abort the test mode.

2) The MOB test message generated by a full function test will appear on all chart

plotters with AIS within range in the form of a SRM (Safe Related Message). The

message is "MOB TEST" with the device´s MMSI number as sender´s identity.

EC Declaration of Conformity

Hereby Alltek Marine Electronics Co declares that this device is in compliance with

the essential requirements R&TTE Directive. All materials, components and

products supplied of the device are in full compliance with RoHS & Weee

directives. A copy of the Declaration of Conformity can be obtained online from

www.alltekmarine.com

RF Exposure warning

Warning: This device generates and radiates RF electromagnetic energy and

requires a Maximum Permissible Exposure of 20cm by operation.

Battery

•

The lithium-ion battery in TB-520 should be replaced only by AMEC or an AMEC

authorized service provider, and must be recycled or disposed of separately

from household waste. Never attempt to replace the TB-520 battery yourself.

•

Do not recharge, puncture, deform, short-circuit the lithium batteries contained

in product or put it in re.

•

The small lithium metal batteries contained in the device can normally be

carried on passenger aircraft in carry-on baggage as a personal item. Always

check with air carrier for any additional restrictions.

End of Life Statement

The symbol above means that your product and/or its battery shall be disposed

of separately from household waste according to local laws and regulations.

S/N(UNIQUE ID):

972160001

BATTERY EXPIRY:

JUL 2015

- 6 -

- 8 -

- 10 -