American Standard Standard 2083 SERIES 설치 지침

{카테고리_이름} American Standard Standard 2083 SERIES에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. American Standard Standard 2083 SERIES 2 페이지. Bathing pool, high gloss acrylic, shown less all fittings

American Standard Standard 2083 SERIES 설치 지침
STANDARD®
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
7-3/4"
(197mm)
3/4"
(19mm)
4"
15-3/8"
(391mm)
(102mm)
4"
(102mm)
32"
(813mm)
+
2-3/8" 13mm
+
(2-3/8) (1/2)
25mm
C/L OF 1/2
(1)
C/L OF
SUPPLIES
DRAIN
AS REQ'D
SHOWER ARM- 1/2 N.P.T.
1-1/4"(32mm) DIA. HOLE
C/L OF CURTAIN ROD
USUALLY 76"(1930mm) FROM
FINISHED FLOOR
C/L OF
(2) 2-1/8"(54mm)
VALVES
DIA. HOLES
OPTIONAL
4"
TO FLOOR
(102mm)
16"
USUALLY
(406mm16)
BETWEEN
65 & 78
(1651 & 1981mm)
1"
(25mm)
20"
(508mm)
TOP OF DECK
4-5/8"
(117mm)
BATH SUPPORT MATERIAL
GENERAL SPECIFICATIONS FOR 2083 BATHING POOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT 3 )
GENERAL INSTALLATION INFORMATION
BATH MAY ONLY BE INSTALLED IN A RECESS TYPE INSTALLATION.
Locate studs as required. Insure rough dimensions are proper, plumb, and square. The following procedure must be
installations: Leveling support stringer should be as indicated. This bath is not self-supporting and must be supported along it's entire
bottom. Support with mortar or grout.
Position bathtub within the recess, check level front to back and side to side, shim as necessary. To secure the tub to wood studs, use
drywall screws with flatwashers or roofing nails immediately above the flange of the bath. To secure the tub to steel studs, use 4" drywall
screws and flatwashers.
SEE PAGE 2 FOR COMPLETE INSTALLATION INFORMATION.
CAUTION: TAKE EXTRA CARE WHEN DRIVING NAILS OR SCREWS TO AVOID DAMAGING THE BATH.
The tile or similar finished floor will be butted against the bottom of the tub apron, also holding the tub in place.
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
753450-100 REV. B
2083 SERIES
BATHING POOL

INSTALLATION INSTRUCTIONS

60"
(1524mm)
70mm
FINISHED
(2-3/4)
WALL
229mm x 305mm
(9 x 12)
FLOOR
CUTOUT
4-1/2"
(114mm)
FINISHED
4"
WALL
(102mm)
4"
SPOUT-
(102mm)
1/2 N.P.T.
3-1/2"
(89mm)
SEE
NOTE
(502mm)
2"
(51mm)
ROUGH
FLOOR
1-1/2 N.P.T. THREADS
1-1/2 O.D. TAILPIECE
60 x 32 x 20 In.
(1524 x 813 x 508mm)
100 Lbs. (45 Kg.)
551 Lbs. (250 Kg.)
54 Gal. (204 L)
18 x 42 In. (457 x 1067mm)
25 X 54 In. (635 x 1372mm)
14 In. (356mm)
41 Lbs./Sq.Ft. (202 Kgs./Sq.m)
20.8
35.3
TH ANK Y OU ...
for selecting an American Standard bath. Your
new bath is shipped to you after careful
inspection. All you need to finish the installation
are your selected fittings.
To insure maximum performance and pleasure
from this product, please follow the instructions
and cautions.
List of Optional Components (not included):
• Standard Bath Caddie 9533.100*
* see your American Standard Distributor
List of Required Components (not included):
• Standard Bath Drain 1501.170*
• Bath Filler*
* see your American Standard Distributor
19-3/4"
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun
Supplies
• Nails
• Putty
• Caulk
(waterproof)
• 1 x 3 or 2 x 4
Stringers
• Drop Cloth
• Mortar Mix
or Grout
© AS America, Inc. 2008
All product names listed herein are trademarks
of AS America, Inc. unless otherwise noted.
used for all