Canon PIXMA MX700 Series 서비스 매뉴얼 - 페이지 6
{카테고리_이름} Canon PIXMA MX700 Series에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Canon PIXMA MX700 Series 44 페이지. Office all-in-one printer
Canon PIXMA MX700 Series에 대해서도 마찬가지입니다: 청소 매뉴얼 (7 페이지), 네트워크 설정 매뉴얼 (32 페이지), 보충 설명서 (6 페이지), 설정 지침 (2 페이지), 브로셔 및 사양 (2 페이지), 기술 정보 (2 페이지)
MX700
2. LIST OF ERROR DISPLAY / INDICATION / TROUBLESHOOTING
Errors and warnings are displayed by the following ways:
1. Operator call errors are indicated by the Alarm LED lit in orange, and the error and its solution are displayed on the LCD in
text and by icon.
2. Messages during printing from a computer are displayed on the MP driver Status Monitor.
3. Error codes are printed in the "operator call/service call error record" area in EEPROM information print
Buttons valid when an operator call error occurs:
1. ON/OFF button: To turn the machine off and on again.
2. OK button: To clear and recover from an error. In some operator call errors, the error will automatically be cleared when
the cause of the error is eliminated, and pressing the OK button may not be necessary.
3. Stop/Reset button: To cancel the job at error occurrence, and to clear the error.
2-1. Operator Call Errors (by Alarm LED Lit in Orange)
Error
No paper in the rear tray. [1000] Rear tray.
No paper in the front
tray.
Front door close error
Paper jam.
Paper jam in the rear
guide.
Ink may have run out.
Ink tank not installed.
Print head not installed,
or not properly installed.
Print head temperature
sensor error.
Faulty EEPROM data of
the print head.
Multiple ink tanks of the
same color installed.
Ink tank in a wrong
position.
Warning: The ink
absorber becomes almost
full.
Error
Message on the LCD
code
There is no paper. Load paper and
press [OK].
[1003] Front tray.
There is no paper. Load paper and
press [OK].
[1250] Paper output tray is closed. Open the
paper output tray.
[1300] The paper is jammed. Clear the paper
and press [OK].
[1303]
[1600] The following ink may have run out.
Replacing the ink tank is
recommended. (U041)
[1660] The following ink tank cannot be
recognized. (U043)
(Applicable ink tank icon)
[1401] Print head is not installed. Install the
print head. (U051)
[1403] The type of print head is incorrect.
Install the correct print head. (U052)
[1405,
1682]
[1681] More than one ink tank of the
following color is installed. (U071)
[1680] Some ink tanks are not installed in
place. (U072)
[1700,
Contact the support center or service
1701,
center for ink absorber replacement.
1710,
Press [OK] to continue printing.
1711]
Confirm that the rear tray is selected as the paper
source. Set the paper in the rear tray, and press the
OK button.
Confirm that the front tray is selected as the paper
source. Set the paper in the front tray, and press the
OK button.
Open the paper output tray.
Remove the jammed paper, and press the OK button.
Replace the applicable ink tank, or press the OK
button to clear the error without ink tank replacement.
When the error is cleared by pressing the OK button,
ink may run out during printing.
Install the applicable ink tank(s) properly, and
confirm that the LED's of all the ink tanks light red.
Install the print head properly.
Re-set the print head. If the error is not cleared, the
print head may be defective. Replace the print head.
Replace the wrong ink tank(s) with the correct one(s).
Install the ink tank(s) in the correct position.
Replace the ink absorber, and reset its counter. [See
3. Adjustment / Settings, (10) Service
Pressing the OK button will exit the error, and enable
printing without replacing the ink absorber. However,
when the ink absorber becomes full, no further
printing can be performed unless the applicable ink
4 / 41
TABLE OF CONTENTS
Solution
mode.]
3-