Bosch DISHWASHER 사용 설명서 - 페이지 25

{카테고리_이름} Bosch DISHWASHER에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch DISHWASHER 30 페이지. Dishwasher bosch
Bosch DISHWASHER에 대해서도 마찬가지입니다: 사용 설명서 지침 (30 페이지), 설치 지침 매뉴얼 (34 페이지), 사용 설명서 (28 페이지), 사용 설명서 (30 페이지), 사용 설명서 (38 페이지), 사용 설명서 (42 페이지), 사용 설명서 지침 (32 페이지), 사용 설명서 지침 (36 페이지), 사용 설명서 지침 (30 페이지), 사용 설명서 (24 페이지), 사용 설명서 지침 (26 페이지), 사용 설명서 지침 (40 페이지), 사용 설명서 지침 (28 페이지), 사용 설명서 지침 (29 페이지), 사용 설명서 (28 페이지), 사용 설명서 (28 페이지), 사용 설명서 지침 (28 페이지), 설치 지침 매뉴얼 (50 페이지), 설치 지침 매뉴얼 (20 페이지), 운영 지침 (24 페이지), 작동 지침 (36 페이지), 사용 설명서 (25 페이지), 사용 설명서 (46 페이지), 사용 설명서 지침 (31 페이지)

Bosch DISHWASHER 사용 설명서

Installation

The required installation dimensions can
be found in the installation instructions.
Level the appliance with the aid of the
height-adjustable feet. Ensure that the
appliance is situated securely on the floor.
– A built-under or integrated appliance
which is installed subsequently as a
free-standing appliance must be
secured to prevent it from overturning,
e.g. by screwing it to the wall or by
installing it under a continuous worktop
which is screwed to adjacent
cupboards.
– The appliance can easily be
installed in a fitted kitchen between
wooden and plastic walls.

Waste-water connection

– The required work sequence can be
found in the installation instructions. If
required, fit a siphon with an drainage
connection.
– Connect the waste-water hose to the
drainage connection of the siphon with
the enclosed parts.
Ensure that the drainage hose is not
kinked, crushed or twisted and that
there is no cover plate in the drainage
to prevent the waste water from flowing
out!

Fresh water connection

– Connect the fresh-water connection to
the tap according to the installation
instructions with the enclosed parts.
Ensure that the fresh-water connection
is not kinked, crushed or twisted.
– When replacing the appliance, always
use a new water supply hose.
Water pressure:
at least 0.05 MPa (0.5 bar), maximum
1 MPa (10 bar). At a higher water
pressure: connect pressure-reducing valve
ahead.
Inlet rate:
minimum 10 litres/minute
Water temperature:
cold water preferred; hot water max.
temperature 60 °C.

Warm water connection *

Wa r m w a t e r c o n n e c t io n
* depending on model
The dishwasher can be connected to cold
or hot water up to max. 60 °C.
Connection to hot water is recommended
if the hot water can be supplied
by energetically favourable means
and from a suitable installation, e.g. solar
heating system with circulation line.
This will save energy and time.
The hot water setting :
to adjust your appliance optimally
to operation with hot water.
It is recommended to have a water
temperature (temperature of the incoming
water) of at least 40 °C and no more than
60 °C.
It is not recommended to connect
the appliance to hot water if the water
is supplied from an electric boiler.
Setting hot water:
– Close the door.
– Switch on ON/OFF switch (.
– Hold down programme button # and
press START button h until : ... is
indicated on the digital display.
– Release both buttons.
The LED for button # flashes and the
digital display )* displays the factory
setting :
.
– Press programme button # until the
factory set value :
the digital display )*.
To change the setting:
– By pressing the 3 button, you can
switch the hot water setting off :
on
:
.
– Press START button h.
The set value is saved.
en
allows you
is indicated on
or
25