Bosch FAP-OC 500Series 설치 매뉴얼 - 페이지 7

{카테고리_이름} Bosch FAP-OC 500Series에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Bosch FAP-OC 500Series 24 페이지. Built-in wall ovens
Bosch FAP-OC 500Series에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (21 페이지), 사용 설명서 지침 (40 페이지), 설치 매뉴얼 (6 페이지), 제품 정보 (40 페이지), 설치 매뉴얼 (28 페이지), 사용자 설명서 (48 페이지), 사용자 설명서 (48 페이지), 설치 매뉴얼 (28 페이지), 사용 및 관리 매뉴얼 (44 페이지), 설치 매뉴얼 (32 페이지), 사용 및 관리 설명서/설치 지침 (40 페이지), 빠른 참조 매뉴얼 (4 페이지), 사용 및 관리 매뉴얼 (27 페이지), 설치 매뉴얼 (32 페이지), 사용 및 관리 매뉴얼 (24 페이지), 설치 매뉴얼 (28 페이지), 서비스 매뉴얼 (41 페이지), 사용 및 관리 매뉴얼 (21 페이지), 설치 매뉴얼 (32 페이지), 서비스 매뉴얼 (36 페이지), 설치 매뉴얼 (32 페이지), 빠른 시작 및 안전 매뉴얼 (13 페이지)

1. Place the microwave oven unit on top of the universal

connector brackets and fasten in place using three

screws per side in the outside set of holes (A). Tighten

the screws securely, but do not overtighten.

Note: The existing screws in the microwave base help

with alignment. When lowering the microwave into

place on the universal connector bracket allow these

screw heads to slide into the slots as shown in the

illustration below. The screw nearest the front of the

microwave slides into the base of the slope at the front

of the bracket.

2. Continue with the unit installation in the section below

describing installation of the warming drawer

microwave/steam oven unit into the wall cabinet.

Mounting the Steam Oven on the Warming

Drawer

Note: Do not place the warming drawer into the wall cabi-

net until after mounting the steam oven on it using the uni-

versal connector brackets.

1. Attach both universal connector brackets to the

warming drawer housing using six of the screws

provided.

2. Mount using the holes to the inside of the unit. Tighten

screws securely, but do not overtighten.

Note: The universal connector brackets are interchange-

able for the left and right sides of the warming drawer. Be

sure the taller vertical edge of the bracket is positioned to

the outside of the warming drawer.

3. Place the steam oven unit on top of the universal

connector brackets and fasten in place using two

screws per side in the inside set of holes (B). Tighten

the screws securely, but do not overtighten.

Note: The existing screws in the sides of the steam

oven base help with alignment. When lowering the

steam oven into place on the universal connector

bracket allow these screw heads to slide into the slots

as shown in the illustration below. The screw nearest

the front of the steam oven slides into the base of the

slope at the front of the bracket.

4. Continue with the unit installation in the following

sections on electrical connection and installing the

steam oven/warming drawer unit into the wall cabinet.

English 5