Andis SUPER AGR+ 사용 및 관리 지침 매뉴얼 - 페이지 4

{카테고리_이름} Andis SUPER AGR+에 대한 사용 및 관리 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Andis SUPER AGR+ 13 페이지. Andis cordless clipper specifications
Andis SUPER AGR+에 대해서도 마찬가지입니다: 사양 (1 페이지)

페이지 인쇄

4. Refer to previous section "Model AGR+ Battery and Charging Stand"

for directions on charging the AGR+ clipper.

Note: If car adapter cable fails to work, the fuse may need to be

replaced. You can purchase a 500mA fuse at an electronic store.

To remove fuse, unscrew cap on car adapter cable (Diagram H).

Use your thumb and forefinger to pull fuse out

of adapter (Diagram I). To replace, set one end

of the new fuse into the opening in the adapter.

Use your thumb to press fuse straight into the

opening in the car adapter. Replace cap. If your

car adapter cable still fails to work you will need

to contact the nearest Andis Service Center.

oPeRATING INsTRUCTIoNs

Please read the following instructions before using your new Andis Clipper. Give it the care that

a fine precision built instrument deserves and it will give you years of service.

ReMovING BLADe seT

To remove blade set, first make sure your clipper motor is switched

"OFF". Push blade release mechanism under blade hinge (Diagram J).

While holding down the blade release mechanism, push down on blade,

then gently pull the blade forward (Diagram K), and slide it off the blade

hinge. If your blade hinge should snap closed and is flush with the

clipper, use a small standard screwdriver to pry the tongue of the

hinge out (Diagram L).

NoTe: Hair may accumulate in the front cavity of the housing under

the blade. If this happens, you can clean out the hair by brushing out

the cavity with a small brush or an old toothbrush while the blade is

off the clipper (See Diagram M for location of cavity being referenced).

RePLACING oR CHANGING BLADe seT

To replace or change your blade set, slide the blade bracket onto the

hinge of the clipper (Diagram N) and with the clipper turned "oN",

push the blade towards the clipper to lock into position.

Diagram M

Diagram L

Diagram G

Diagram I

Diagram H

Diagram J

Diagram K

Diagram N

UseR MAINTeNANCe

The internal mechanism of your motor clipper has been permanently lubricated by the factory.

Other than the recommended maintenance described in this manual, no other maintenance should

be performed, except by Andis Company, or an Andis Authorized Repair Service Station.

CARe AND seRvICING oF YoUR ANDIs CLIPPeR BLADes

Blades should be oiled before, during, and after each use.

If your clipper blades leave streaks or slow down, it's a sure

sign blades need oil. Place a few drops of oil on the front and

side of the cutter blades (Diagram O). Wipe excess oil off blades

with a soft, dry cloth. Spray lubricants contain insufficient oil for

good lubrication, but are an excellent clipper blade coolant. Always

replace broken or nicked blades to prevent injury. You can clean the

excess hair from your blades by using a small brush or worn out

toothbrush. To clean the blades, we suggest to immerse the blades only

into a shallow pan of Andis Clipper Oil, while the clipper is running.

Any excess hair and dirt that has accumulated between the blades

should come out. After cleaning, turn your clipper off and dry blades

with a clean dry cloth and start clipping again. If upon cleaning your

blades you find that the blades will still not cut, there may be a few

fine pieces of hair trapped between the upper and lower blade. If this

happens, you will need to snap the blade off the clipper. Proceed to

slide the upper blade to one side, without loosening the tension spring

or moving the upper blade completely out from under the tension spring (See Diagram P for

position of blade). Wipe the surface between the blades clean with a dry cloth, then place a drop

of clipper oil where the upper and lower blades meet and also in the guide slot of the tension spring

(Diagram N). Now slide the upper blade to the opposite side of the lower blade and repeat this

process. After completing this procedure, slide the upper blade, centering it over the lower blade.

Handle or store your Andis Clipper with the blades down so excess oil will not run into the

clipper case.

CAUTIoN: Never handle your Andis Clipper while you are operating a water faucet and never hold

your clipper under a water faucet or in water. There is danger of electrical shock and damage to your

clipper. ANDIs CoMPANY will not be responsible in case of injury due to this carelessness.

Diagram O

Diagram P