ATL Delta 820 사용자 설명서 - 페이지 2

{카테고리_이름} ATL Delta 820에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. ATL Delta 820 2 페이지.

페이지 인쇄

Preparing to use your

Delta 820

INITIAL CHECK

Our telephones are checked, tested and leave us in

perfect condition. If yours is damaged, please return

it to your supplier with proof of purchase, for a

replacement.

CONNECTION

The Delta 820 telephone can be connected either to

a Direct Exchange Line, or as an extension to a

compatible company exchange (PABX).

HANDSET CORD

This cord will require connection between the

telephone and handset. Take any end of the

handset cord, locate the port on the left hand side of

the Delta 820 and simply push to locate. Connect

the other end to the base of the handset to

complete.

LINECORD

The Delta 820 arrives with a linecord for connection

to a standard BS6312 BT-socket. The line socket

can be found on the rear of the telephone, plug your

linecord into this port first and the other end to your

telephone line termination point.

An RJ11 or an RJ45 linecord are available as an

option, ask your supplier for details.

Using your Delta 820 with

the Handset

RECEIVING CALLS

Incoming calls will be announced by the audible

ringer and flashing LED. To answer the call, simply

lift the handset.

ADJUSTING YOUR RINGER VOLUME

The ringer volume is controlled by a 2 position

switch located at the rear of the telephone and

indicated by a picture of a bell.

MAKING A CALL VIA THE HANDSET

Pick up the handset and listen for dial tone

Dial the required telephone number

(Note: making external calls from a company

exchange (PABX) may require the number to be

prefixed by an access digit, normally '9').

Using your Delta 820 with

Hands Free

Whether it's having both hands available, or

conference

calling

with

colleagues,

speakerphone feature of the Delta 820 is seen by

many as a valuable benefit. Operation is via the

'SPEAKER' key, (providing the handset is left in

place). Speaker volume may be adjusted via the 3

position switch on the rear of the phone.

Features and Facilities

TRANSFER KEY (RECALL / FLASH)

The Delta 820 telephone is provided with a

'TRANSFER' key, required by modern public and

private exchanges, in order to gain access to various

features such as 'transferring a call'.

REDIAL KEY

If you wish to redial the last number you dialled, you

can do so by lifting the handset and pressing the

'REDIAL' button.

HOLD KEY

The microphone in the handset can be turned off

(mute) in order for you to refer to a colleague without

your caller hearing you.

When using the handset. Pressing the 'HOLD'

button turns off the microphone and presents the

calling party with comfort music.

Pressing the 'HOLD' button turns the microphone

back on.

Similarly when using the handsfree option. Pressing

the 'HOLD' button turns off the microphone and

presents the calling party with comfort music.

Pressing

the

'SPEAKER'

button

turns

microphone back on.

MEMORY KEYS

The Delta 820 comes with 10 non volatile (no

batteries required) memories, for efficient speed

dialling of commonly used numbers. Making a call

via these keys is as simple as lifting the handset and

pressing the desired memory key.

To identify these keys it will first be necessary to

write the names of the company or individuals the

keys will represent on to the label provided. This

label is held in place by a clear plastic cover, which

can be removed by simply un-clipping the retaining

clips on the edges and lifting clear.

With the memory card removed you are now ready

to program the memory buttons.

Lift the handset and press the 'STORE' key. (This is

a translucent button found under the 1

button).

the

Enter the telephone number to be dialled. If your

telephone is on a PABX extension, it may be

necessary to enter the access digit (9) before the

number to be entered.

Finally press the memory key to be programmed.

The

message

waiting

button

programmed in the same way with the PABX's

feature code to retrieve stored voicemails.

WALL MOUNTING

The phone can be wall mounted. The handset hook

guide will need to be adjusted. This is achieved by

sliding it upwards, rotated it by 180 degrees and

returning it to its slot. The base of the phone can be

secured to a suitable surface; screws should be

83mm apart.

Help

If the telephone appears to be faulty when first

connected, a few simple checks may help to identify

some possible problems, as listed below:

NO DIAL TONE

•

Ensure you are using the cables that

the

came with this phone.

•

Check that the telephone plug is fully

inserted in the socket

•

If it is, try connecting the telephone into

another socket, if available. If dial tone is

now heard, the original socket is faulty.

•

Alternatively,

try

connecting

telephone

into

your

telephone gives dial tone, then your new

telephone is probably faulty.

Further concerns may also be addressed by

calling our Technical Support Department on

0845 421 0730 or visiting our website,

www.atltelecom.com/support

memory

can

also

another

socket.

this