Atlantic ColorFalls CC12 운영 매뉴얼 - 페이지 2

{카테고리_이름} Atlantic ColorFalls CC12에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Atlantic ColorFalls CC12 14 페이지. Color changing colorfalls
Atlantic ColorFalls CC12에 대해서도 마찬가지입니다: 운영 매뉴얼 (14 페이지)

페이지 인쇄

Introduction

Thank you for choosing Atlantic's Color Changing Colorfalls. The Colorfalls are

designed for use in Pond-free and fountain applications. The Color Changing

Colorfalls feature a larger opening which produces a thicker water sheer and less

clogging from debris in the water, a remote controlled Color Changing LED light

bar, and a removable back plate that provides access to the interior of the spillway

for easy maintenance and winterizing.

Prior to Operation and Installation

Caution:

• DO NOT operate this product under any condition other than those

for which it is specified. Failure to observe these precautions can lead

to electrical shock, product failure, or other problems.

• Follow all aspects of electrical codes when installing the Color

Changing Colorfalls.

• To reduce the risk of electrical shock, connect only to a 110 volt

receptacle protected by a ground fault circuit interrupter (GFCI).

• The input power to the Color Changing Control Module is 12 volt AC.

The Control Module can be connected to a larger outdoor lighting

transformer; however this must be done between the Control Module

and the transformer. Removing the Control Module or tampering with

the cord between the Control Module and the Colorfalls will damage

the light bar and void warranty.

• The Control Module is weather resistant with an IP54 rating. Do not

submerse the Control Module or expose it to heavy rainfall. It must be

mounted off the ground close to the power source. Failure to do so will

void the warranty.

• Colorfalls are designed for use in Pond-free and fountain applications.

Colorfalls are not intended for use in water gardens or any pond with

plant or aquatic life.

It is recommended that the entire Colorfalls be easily accessible. If this is not an

option, access to the rear of the Colorfalls is required for maintenance purposes.

The Colorfalls can support 40 lbs. per linear foot (e.g. a 24" Colorfalls can support

80 lbs.). If the weight on the weir exceeds that amount, you will need to provide a

lintel support for the added weight. This support should still make contact with the

weir to prevent it from shifting.

See the chart below for the recommended placement of the Colorfalls above the

basin or pool. If the placement of the Colorfalls exceeds the recommended height,

water loss will increase significantly due to splash and wind drift.

Maximum Falls

Colorfalls

Height Above Basin

CC06

CC12

CC24

CC36

Installation of Color Changing Colorfalls

The opening in the wall where the Colorfalls will be placed is important to the

function of the Colorfalls. If it is not level and free of debris the Colorfalls will not

function properly. The base of Colorfalls body as well as the bottom of the spillway

lip must be supported by the

opening in which it is placed.

The top side of the opening

must also be in contact with the

Colorfalls to prevent it from

shifting. See Figure 1 for the

proper sizing of the opening for

the Colorfalls.

Plumbing A Single Colorfalls

Each Colorfalls spillway is

equipped with three convenient

1½" PVC socket inlets to

accommodate 1½" PVC fittings

or pipe. Choose one or more of

the three inlets for plumbing: you

can plumb either directly into the

back center of the unit, or from one or both sides and close off the unused inlet(s)

with the provided plugs. All fitting attachments can be made using standard PVC

Glue and Cleaner. Follow the instructions on your PVC Glue and Cleaner for the

proper use of those materials.

Installing a ball valve (not included) on the feed line between the pump and the

Colorfalls is recommended for added control of water flow.

Flow Rate

18"

600 GPH

24"

1200 GPH

30"

2400 GPH

36"

3600 GPH

Figure 1

½"