DSC WLS904P-433 빠른 시작 매뉴얼 - 페이지 2

{카테고리_이름} DSC WLS904P-433에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DSC WLS904P-433 2 페이지. Wireless motion detector

페이지 인쇄

The coils and antenna on the Motion Detector circuit board are very

sensitive components precisely adjusted for maximum performance.

Do not touch the coils or antenna! Even minor distortions can affect the

performance of the Motion Detector

performance of the Motion Detector. . . . .

performance of the Motion Detector

Enrolling a WLS904P

On the back of the PIR housing, there will be two serial numbers: a five-

digit number and a six-digit number. Please refer to your receiver

installation manual for information on which serial number should be

enrolled. NOTE: If using a WLS900 system, you must use the five-digit

NOTE: If using a WLS900 system, you must use the five-digit

serial number.

Changing the Sensitivity Setting

The WLS904P features "Fast" and "Slow" settings on

jumper J1 which is used to configure the detector for

the weight of the pet(s) and the environment. For an

environment with a single pet whose weight does not

exceed 30lbs (13.6kg) the jumper should be set to

"Fast" setting. In an environment with single or

multiple pets whose combined weight is greater than

30lbs (13.6kg) but not greater than 60 lbs. (27.3kg)

the jumper must be set to the "Slow" setting. In a

hostile environment or where the installation

conditions can not be controlled J1 must be set to the

"Slow" setting.

The diagram above shows the jumper location. To change the setting from

Fast to Slow, move the jumper over one pin, as shown in the diagram.

High Traffic Shutdown Mode

To prolong battery life, the motion detector uses a feature called High

Traffic Shutdown. When motion is detected, the device will transmit to the

receiver and will then shutdown for six minutes. Should motion be detected

during this shutdown time, the unit will not transmit the event to the receiver

but will re-set the shutdown time to three minutes, regardless of how much

of the six minute shutdown has elapsed. If motion is detected anytime

during the three minute shutdown the detector will not transmit but will reset

the shutdown time to three minutes again. When motion is detected after a

full three minute shutdown period the detector will then transmit to the

receiver and initiate the six minute shutdown sequence again.

The High Traffic Shutdown Mode affects testing the motion detector in two ways:

When performing the module placement test, the unit must be tampered

by removing the unit from the backplate and replacing it. The placement

test cannot be performed by creating motion in front of the device.

When performing a system test, the unit must be left idle for three minutes

before testing can be performed. Once three minutes has passed, create

motion in front of the detector to see if the device is both detecting motion

and transmitting to the receiver.

Motion Detector Transmission Delay

A motion detector transmission is always delayed by six seconds. This is

necessary to prevent false alarms caused by a motion sensor transmitting

before a delay zone has a chance to report. This six-second delay cannot

be altered or disabled.

Walk Test Mode

The motion detector has a walk test mode which will activate an LED for

testing purposes. During normal operation, the LED will not turn on.

To put the detector in walk test mode, create a tamper by removing the

detector from its backplate and then replacing it. Each time the detector

senses motion, it will turn on the red LED. Five seconds after motion is

detected, the detector will send a signal to the receiver, and the LED will

flash rapidly 5 times. The detector will be in walk test mode until it has sent

10 transmissions.

To verify the pet immunity of the detector place the animal(s) within the

coverage area and then move out of the zone. Encourage the pet to move

around as it normally would and ensure that it moves across the detection

pattern of the detector. Verify that no alarm is initiated.

To test for catch performance of humans, create motion in the entire area

where coverage is desired by walking perpendicular to the lens pattern.

Should the coverage be incomplete, readjust or relocate the detector.

The Walk T

The W

firealarmresources.com

R R R R R efer to the PC5132 and PC5010 Installation Instructions for UL/ULC

efer to the PC5132 and PC5010 Installation Instructions for UL/ULC

requirements. F

or UL/ULC installations where the WLS904P is used on

requirements. For UL/ULC installations where the WLS904P is used on

requirements. F

or UL/ULC installations where the WLS904P is used on

entry or exit delay zones, the entry delay must not be longer than 39

seconds, and the exit delay must not be longer than 54 seconds.

alk Test Mode will override the High T

alk T

est Mode will override the High Traffic Shutdown Mode.

est Mode will override the High T

alk T

est Mode will override the High T

Detection Pattern

"Fast" Setting - 40ft x 40ft

"Slow" Setting - 35ft x 35ft

SIDE VIEW

raffic Shutdown Mode.

TOP VIEW