Atwood G10-3E 매뉴얼 - 페이지 4

{카테고리_이름} Atwood G10-3E에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Atwood G10-3E 17 페이지. L.p. gas water heater
Atwood G10-3E에 대해서도 마찬가지입니다: 설치 운영 및 유지보수 (17 페이지), 설치, 작동 및 유지보수 지침 (9 페이지)

페이지 인쇄

FOR WHITE RODGERS

CONTROL (

a. Turn lighting control knob (

against stop while lighting pilot burner (

b. Allow pilot to burn thirty seconds then release lighting control

knob.

c. Turn lighting control knob (

d. If pilot does not remain lit, repeat operation allowing longer peri-

od before releasing lighting control knob.

e. Set temperature selection lever (

and hot position.

f. Close access door.

FOR A ROBERTSHAW UNITROL

a. Turn lighting control dial (

b. Depress and hold reset push button (

burner (

9-D).

FIG

c. Allow pilot to burn thirty seconds before releasing reset push

button.

d. If pilot does not remain lit, repeat operation allowing longer peri-

od before releasing reset push button.

e. Turn lighting control dial (

f. Set temperature control dial (

between warm and hot.

g. Close access door.

4. For complete shut down and before servicing, turn gas control knob

(

7-B or

8-B) to OFF position. When water heater is not in use

FIG

set temperature control lever (White Rogers

to lowest possible position.

SCALDING INJURY

Setting temperature control dial at a higher position will produce exces-

•

sively hot water.

The temperature knob or lever is factory adjusted to its lowest dial

setting. We recommended the mid-point position between warm and

hot, as noted above. This will provide for energy efficient operation

and sufficient hot water. Valves for reducing point of use temperature

by mixing cold and hot water are available. Consult a licensed

plumber or local plumbing authority.

5. To Adjust Main Burner (

FIG

1. Loosen air shutter screw (

2. Slide air shutter (

9-B) to right until some yellow appears in

FIG

main burner flame.

3. Move air shutter (

9-B) to left until yellow disappears.

FIG

4. Retighten air shutter screw (

Read MAINTENANCE AND CARE INSTRUCTIONS

ELECTRONIC IGNITION OPERATION

1. Refer to WIRING DIAGRAM. Place remote switch in ON position.

2. If remote switch light stays on longer than 15 seconds, place

remote switch in OFF position and wait 5 minutes.

3. Repeat step one.

4. For complete shut-down and before servicing:

a. Place remote switch in OFF position.

b. Remove red wire from left hand terminal of ECO switch (ECO to

valve).

5. If heater fails to operate due to high water temperature, a lockout

condition occurs (indicator light on). After water cools, reset switch

in OFF position for at least 30 seconds, then turn to ON position.

6. If a lockout condition persists contact an Atwood Service Center.

Read

MAINTENANCE AND CARE INSTRUCTIONS

MAINTENANCE

PILOT RELIGHT OPERATION

1. Turn the switch located on the spark module to the ON position.

2. Read PILOT OPERATION instructions.

3. For complete shut down, turn lighting control knob on thermostat

and spark module switch to the OFF position.

Read

MAINTENANCE AND CARE INSTRUCTIONS

FIG

7-B) to PILOT position and hold

FIG

9-D).

FIG

7-B) to ON position.

FIG

7-A) at mark between warm

FIG

(

FIG

8-B) to PILOT position.

FIG

8-A) while lighting pilot

FIG

8-B) to ON position.

FIG

8-C) at mid-point position

FIG

) or dial (Robertshaw

CAUTION

9):

9-A).

FIG

9-A).

FIG

& ELECTRONIC IGNITION

COMBO gas/electric ELECTRIC OPERATION

1. For gas operation refer to Pilot, Pilot Relight or Electronic Ignition

OPERATION section (as applicable).

2. For electrical operation use switch at the rear of water heater.

3. Completely fill tank with water.

4. Turn switch ON (

FIG

: Turning power on to heater without water covering heating ele-

NOTE

ment may burn out element and void warranty.

5. Check for proper operation. Water temperature is set at 140°F

(60°C).

6. If the manual reset high temperature limit switch should operate,

reset switch (

11-A) by depressing with pencil or other nonmetal-

FIG

lic object. If still experiencing problems contact an authorized

Atwood Service Center or Atwood Service Department.

Read

MAINTENANCE AND CARE INSTRUCTIONS

SERVICE CALLS & QUESTIONS

Location and phone numbers of qualified Service Centers can be found

at our website http:/www.atwoodmobile.com or call 815-877-5700 to

have a Service Center List mailed.

FIRE OR EXPLOSION

)

Shut off gas supply at LP container before disconnecting a gas line.

•

Keep control compartment clean and free of gasoline, combustible

•

material, and flammable liquids and vapors.

AFTERMARKET WATER HEATING ELEMENT DEVICES

EXPLOSION / BURN INJURY

alter water heater, it will void warranty.

•

DO NOT

Aftermarket heating elements, they can lack critical safety

•

DO NOT USE

controls.

Use of Aftermarket heating elements can lead to an out of control

•

heating of water tank and a catastrophic wet side explosion.

The use of manufacturer's aftermarket heating element devices may

also result in damage to components or water heater. Atwood's written

warranty states - "failure or damage resulting from any alteration to

our water heater is the owner's responsibility". Any alteration, like the

addition of an aftermarket heating element device, will void the warranty.

GENERAL INFORMATION

• LP and Water system must be turned on.

• Have gas pressure tested periodically. Should be set at 11 inches of

water column with three appliances running.

• Drain water heater at regular intervals (at least one time during the

year).

• Drain water heater before storing RV for the winter or when the

possibility of freezing exists.

• Keep vent and combustion air grill clear of any obstructions.

• Periodically, compare flame of main and pilot burners with

and main burner adjustments in

• When water heater is not in use set temperature control lever (White

Rogers) or dial (Robertshaw) to lowest possible position. This will

reduce the effects of low outdoor temperatures on calibration of

temperature control mechanism.

ELECTRONIC IGNITION MAINTENANCE

• The water heater comes factory-equipped with a fused circuit board,

which will protect the circuit board from wiring shorts. If the fuse

should activate, the water heater will not operate. Before replacing

the fuse, check for a short external to the board. Once the short is

corrected, replace the 2 amp fuse with a mini ATO style fuse. Do not

install a fuse larger than 3 amps.

11-B) (located at rear of water heater).

WARNING

HOW TO OPERATE YOUR WATER HEATER

➈

FIG