Auber Instruments SYL-1813-MR 사용 설명서 - 페이지 2

{카테고리_이름} Auber Instruments SYL-1813-MR에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Auber Instruments SYL-1813-MR 3 페이지. Multifunction automotive gauge

페이지 인쇄

AUBER INSTRUMENTS

Note 3. For adjusting the display value; applies only to the temperature

readings. Display = measurement * PSbF.

Note 4. Digital filter. Filt = 0, no filter; 1, weak; 2, medium; 3, strong.

Table 1. Sensor Input Type Options

Symbol

Input Type

TC, Type T

-200 ~ 400° C

TC, Type R

-50 ~ 1600° C

TC, Type J

-200 ~ 1200° C

TC, WRe3

WRE

0 ~ 2300° C

–WRe25

VDO

Vdo

water/oil

50 ~ 150° C

Temp

TC, Type S

-50 ~ 1600° C

TC, Type K

-200 ~ 1300° C

TC, Type E

-200 ~ 900° C

RTD,

P100

-200 ~ 600° C

PT100

RTD, Cu50

-50.0~ 150.0° C

Cu50

0~375Ω

375r

Pressure

0~75mV

75mV

Current

0~30mV

30mV

Display range

0~5V

1-5V

1~5V

to -1999 ~ 9999

10V

0~10mA

10mA

20mA

0~20mA

4 -–

4~20mA

20mA

(Note: TC, thermocouples.)

D.1.B) How to change basic parameters (see Figure 4)

Operation Mode

Enter Code

SET

0089

XXXX

SET

Figure 4. Basic Parameter Setting Flow Chart.

D.2 Alarm parameter (press SET then input code 0001 to enter)

D.2.A) Alarm parameters description

Symbol

Name

Description

AH1

J1 pull in value

AH1

AL1

J1 drop out value

AL1

2021.05

Range

Res.

Accy.

1° C (° F)

0.3%

1° C (° F)

0.3%

1° C (° F)

0.2%

1° C (° F)

0.2%

1° C (° F)

0.3%

1° C (° F)

0.3%

1° C (° F)

0.2%

1° C (° F)

0.2%

1° C (° F)

0.2%

0.1° C

0.5%

(° F)

0.2%

0.1%

can be set

16 bit A/D

0.1%

0.3%

0.2%

Symbol

Input Type

SET

XXXX

inty

Input Low Limit

SET

XXXX

PuL

Input High Limit

SET

XXXX

PuH

Deci m al Point

SET

XXXX

DOT

Input Offset

SET

XXXX

psb

Range Coefficient

SET

XXXX

Psbf

Temperature Unit (C/F)

SET

corf

Digital Filter

FILT

end

Setting Range

-1999 ~ 9999

AH2

AL2

End

Note 5a. Relay action setting.

1) Set AH1 = AL1, relay is disabled.

Impedance

2) Set AH1 > AL1, relay is for high limit alarm. See Figure 5 (left).

100K

3) Set AH1 < AL1, relay is for low limit alarm. See Figure 5 (right).

100K

(0.2mA)

100K

Figure 5. Reply (J1) action when the alarm is set as high alarm (left) and low

(0.2mA)

alarm (right).

(0.2mA)

Note 5b. AH2 and AL2 parameters should be ignored. They are associated with

J2 relay, which are not available in this gauge.

(0.2mA)

100K

D.2.B) How to change alarm parameters

The procedure to change alarm parameters is similar to the procedure for basic

100K

parameter setting shown in Figure 4 except the access code is 0001 instead of

100K

0089.

100K

D.3. Peak value (press SET then input code 0037 to enter)

150Ω

D.3.A) Peak value description

150Ω

Symbol

Name

MA-t

MI-t

End

SET

Note 6. Peak function is inter-locked.

1) When MA is turned off, MA-t cannot be set to "on".

SET

2) When MI is turned off, MI-t cannot be set to "on".

D.3.B) How to change peak value parameters

SET

The procedure to change the peak value settings is similar to the procedure for

changing basic parameters in Figure 4 except access code is 0037 instead of

SET

0089.

SET

D.3.C) Reset the peak value

The peak values is stored in the memory even the meter is powered off. To reset

SET

them, change display to show MA, MA-t, MI or MI-t. Then, press and hold "Λ"

key for 3 seconds. The display will show "- - - - ", indicating the memory (for all

SET

four parameters) is reset. The meter will start to catch the new peak after 2

seconds.

E. Application Examples

E.1 Exhaust gas temperature (EGT)

Auber's EGT probes are type K thermocouples. To read an Auber's EGT probe,

set the sensor type inty to "k" (k). The gauge is preset for the EGT application.

Wire the meter as the diagram below (Figure 6) and it is ready to go.

(Continue on next page)

Initial

Note

Setting

900

800

WWW.AUBERINS.COM

N.A.

Exit

Description

Setting Range

Maximum value

On/off

Time of maximum

On/off

Minimum value

On/off

Time of minimum

On/off

Exit

900

800

Initial

Note

Setting

Off

P2/3