Apollo XPander XPA-OH-13023-APO 설치 매뉴얼 - 페이지 2

{카테고리_이름} Apollo XPander XPA-OH-13023-APO에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Apollo XPander XPA-OH-13023-APO 2 페이지. Smoke and heat detectors

페이지 인쇄
Apollo XPander XPA-OH-13023-APO 설치 매뉴얼
Installation
All detectors must be sited in accordance with the original approved design and site
survey details. Where practical the detector's LED should face towards the room's
entrance.
1.
Twist the ceiling mounting plate anti-clockwise to remove it from the mounting base.
2.
The ceiling mounting plate must be fitted using both mounting holes and suitable
fixings or fasteners. (Fig 1)
Note: Any screw heads must be flush or semi flush with the internal surface of the ceiling
mount otherwise the battery PCB may be damaged.
3.
Attach the mounting base to the ceiling mounting plate ensuring the tamper switch
spring assembly makes contact. Locate the three lugs and twist clockwise.
4.
Fit the detector to the mounting base.
5.
Fit the power jumper shorting link and commission the unit according to the XPander
commissioning guide PP2286.
Locking Mechanism
The detectors can be locked into the base by removing a tab as shown in Fig.2.
To unlock the detector, insert a 1.5mm hex driver or similar diameter tool into the small hole
opposite the XPERT card and twist the detector anti-clockwise.
The XPander base module can be locked to the mounting plate by means of a grub screw.
Access to which is through the base module cover label opposite the XPERT card
The address of the unit is set using the XPERT card, see table overleaf. Commission the
detector according to the XPander commissioning guide PP2286.
XPERT card insertion and removal
Removal requires access to the inner section of the base. Detach the detector from its
base. Insert a flat-blade screwdriver just inside the rim of the base above the XPERT card
and disengage the card retaining clip whilst pulling the XPERT card out.
© Apollo Fire Detectors Limited 2007 TP
Fig 1 Mounting details
Snip along marked lines and remove this
part to lock the detector to the base.
© Apollo Fire Detectors Limited 2008/TP
Fig 2. Locking Mechanism
2
XPERT Card Addressing
The XPander XPERT card is specifically designed for XPander products and has profiled
address pips for ease of installation. The use of standard XPERT cards is not recommended.
Select the desired address and remove the pips indicated in black. Remove pips with a
XPERT card addressing forXP95 and Discovery
small screwdriver.
Select the desired address and remove the pips indicated in black. Remove pips with a small screwdriver.
1
2
3
4
5
6
1
2
3
4
5
6
16
17
18
19
20
21
16
17
18
19
20
21
31
32
33
34
35
36
31
32
33
34
35
36
46
47
48
49
50
51
46
47
48
49
50
51
61
62
63
64
65
66
61
62
63
64
65
66
76
77
78
79
80
81
76
77
78
79
80
81
91
92
93
94
95
96
91
92
93
94
95
96
106
107
108
109
110
111
106
107
108
109
110
111
121
122
123
124
125
126
121
122
123
124
125
126
7
8
9
10
11
12
13
7
8
9
10
11
12
13
22
23
24
25
26
27
28
22
23
24
25
26
27
28
37
38
39
40
41
42
43
37
38
39
40
41
42
43
52
53
54
55
56
57
58
52
53
54
55
56
57
58
67
68
69
70
71
72
73
67
68
69
70
71
72
73
82
83
84
85
86
87
88
82
83
84
85
86
87
88
97
98
99
100
101
102
103
97
98
99
100
101
102
103
112
113
114
115
116
117
118
112
113
114
115
116
117
118
3
14
15
14
15
29
30
29
30
44
45
44
45
59
60
59
60
74
75
74
75
89
90
89
90
104
105
104
105
119
120
119
120