ADEMCO LYNX 사용자 설명서 - 페이지 15
{카테고리_이름} ADEMCO LYNX에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. ADEMCO LYNX 17 페이지.
ADEMCO LYNX에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (8 페이지), 시스템 매뉴얼 (14 페이지)
페이지 인쇄
81
ZONE LISTS FOR OUTPUT DEVICES
Fill in the required data on the worksheet below and follow the procedure in the installation manual as you enter the data
during the displays and prompts that appear in sequence.
Note:
Record desired zone numbers below. More or fewer boxes than shown may be needed, since any list may
include any or all of system's zone numbers.
Zone List 1: Started or stopped by zone numbers (enter 00 to end entries).
[28] [32]
Zone List 2: Started or stopped by zone numbers (enter 00 to end entries).
[29] [33]
Zone List 3: Started or stopped by zone numbers AND/OR assignment of Chime zones (enter 00 to end entries)
[02] [03]
ENROLL AS "UR" OR "RF"
ENROLL AS "UR" OR "RF"
LOOP 3
NOTE: You must enroll loop 4 on the 5801, 5804 and 5804BD transmitters, regardless of whether the other loops
are being used.
SPECIAL MESSAGES
EE = DATA ENTRY ERROR (invalid field number entered while programming; re-enter valid field number).
FC = Communication Failure
EA = Exit Alarm
CA = Cancel Alarm
CC = Modem Communication (system is in communication with the central station)
After powering up, AC, dI (disabled) will be displayed after approximately 4 seconds. This will revert to the Real-
time Clock in approximately 1 minute. To bypass this delay, press: [#] + [0].
5800 SERIES LOOP NUMBERS
LOOP 3
LOOP 2
LOOP 1
LOOP 4
YOU MUST
ENROLL THIS
BUTTON
5 8 0 2 / 5 8 0 2 C P
ENROLL AS "BR"
5 8 0 1
YOU MUST
ENROLL THIS
BUTTON
LOOP 4
LOOP
1
5 8 0 2 M N
5 8 0 4
ENROLL AS "BR"
LOOP 2
YOU MUST
ENROLL THIS
BUTTON
LOOP 4
LOOP 1
5 8 0 6 / 5 8 0 7 / 5 8 0 8
(5806 SHOWN)
•
• •
• • •
SET
ENROLL AS "RF"
• •
• •
• •
•
HOUSE
•
CODE
5 8 0 4 B D
ENROLL AS "BR"
LOOP
LOOP
2
(REED)
(REED)
LOOP 1
(TERMINALS)
LOOP
1
ALTERNATE
5 8 1 6
ENROLL AS "RF"
FOR LOOP 2
LOOP
1
(PRIMARY)
LOOP 3
2
(AUX. CENTER)
LOOP 2
3
LOOP 1
(AUX. RIGHT)
5 8 1 7
ENROLL AS "RF"
LOOP
2
(REED)
LOOP 1
(TERMINALS)
5 8 1 9
ENROLL AS "RF"
LOOP 3
(TERMINALS)
LOOP
1
LOOP
1
(MOTION)
5 8 4 9
ENROLL AS "RF"
15 –
–
2
LOOP 1
(TERMINALS)
5 8 1 6 M N
POSITION
ENROLL AS "RF"
LOOP
1
5 8 1 8
ENROLL AS "RF"
5 8 2 7
SET HOUSE CODE
5 8 2 7 B D
SET HOUSE CODE
LOOP
1
(MOTION)
5 8 9 0
ENROLL AS "RF"
.etc.
.etc.
.etc.