ADEMCO LYNX 사용자 설명서 - 페이지 6

{카테고리_이름} ADEMCO LYNX에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. ADEMCO LYNX 17 페이지.
ADEMCO LYNX에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (8 페이지), 시스템 매뉴얼 (14 페이지)

페이지 인쇄

TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES ( 59– 76, & 89):

With a 3+1 or 4+1 Standard Format: Enter a code in the first box: 1–9, 0, B, C, D, E, or F. Enter "#+10" for 0, "#+11" for B,

"#+12" for C, "#+13" for D, "#+14" for E, "#+15" for F.

A "0" ( not "#+10") in the first box will disable a report.

A "0" ( not "#+10") in the second box will result in automatic advance to the next field when programming.

With an Expanded or 4+2 Format: Enter codes in both boxes (1st and 2nd digits) for 1–9, 0, or B–F, as described above.

A "0" ( not "#+10") in the second box will eliminate the expanded message for that report.

A "0" ( not "#+10") in both boxes will disable the report.

With Ademco Contact ID Reporting: Enter any digit (other than "0") in the first box, to enable zone to report (entries in the

second boxes will be ignored).

A "0" ( not "#+10") in the first box will disable the report.

Examples: For Code 3 (single digit), enter:

For Code 3 2 (two digits), enter:

For Code B 2 (Hexadecimal), enter:

SYSTEM STATUS REPORT CODES ( * 59– * 68)

Field

Function

EXIT ERROR REPORT CODE

TROUBLE REPORT CODE

BYPASS REPORT CODE

AC LOSS REPORT CODE

LOW BAT REPORT CODE

TEST REPORT CODE

OPEN REPORT CODE

ARM AWAY/STAY RPT CODE

RF XMTR LOW BAT REPORT CODE

CANCEL REPORT CODE

RESTORE REPORT CODES ( * 70– * 76)

ALARM RESTORE RPT CODE

TROUBLE RESTORE RPT CODE

BYPASS RESTORE RPT CODE

AC RESTORE RPT CODE

LOW BAT RESTORE RPT CODE

RF XMTR LO BAT RST RPT CODE

TEST RESTORE RPT CODE

OUTPUT AND SYSTEM SETUP ( * 80– * 92)

80 POWERLINE CARRIER DEVICES

81 ZONE LISTS FOR DEVICES

83 SEQUENTIAL MODE (Also entered from field 56): See procedure later in this manual.

84 ASSIGN ZONE VOICE DESCRIPTORS. See procedure later in this manual.

85 RECORD CUSTOM VOICE DESCRIPTORS. See procedure later in this manual.

3 | 0

3 | 2

#+11 | 2

Programmed Values

[1]

2nd digit is automatically sent as 2nd digit of the zone alarm report

code programmed in 56, if expanded or 4+2 reporting is selected.

[1,0]

†† [1]

††

AWAY

STAY

[1,0]

[1]

2nd digit is automatically sent as 2nd digit of the zone alarm report

code programmed in 56, if expanded or 4+2 reporting is selected.

[1,0]

Program *80 and *81 only if Powerline Carrier Devices or chime by

zone are to be used. See procedure later in this manual.

6 –

–

[

] = Table 1 Default Value

[1,1] (

†† 2nd digit is automatically sent as the user

number if expanded or 4+2 reporting is selected.)