GREAT PLANES YAK-55M Yakovlev 사용 설명서 - 페이지 14

{카테고리_이름} GREAT PLANES YAK-55M Yakovlev에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. GREAT PLANES YAK-55M Yakovlev 20 페이지. Arf plane

페이지 인쇄

Apply the Decals

The box photographs show the location of the decals on

the airplane. Refer to the box for the exact placement of the

decals. The following tips may be useful for applying them.

❏

1. Remove the decals from the decal sheet.

❏

2. Be certain the model is clean and free from oily

fingerprints and dust. Prepare a dishpan or small bucket with

a mixture of liquid dish soap and warm water—about one

teaspoon of soap per gallon of water. Submerse the decal

in the soap and water and peel off the paper backing. Note:

Even though the decals have a "sticky-back" and are not the

water transfer type, submersing them in soap & water allows

accurate positioning and reduces air bubbles underneath.

❏

3. Position decals on the model. Holding the decals down,

use a paper towel to wipe most of the water away.

❏

4. Use a piece of soft balsa or something similar to

squeegee remaining water from under the decal. Apply the

rest of the decals the same way

GET THE MODEL READY TO FLY

Check the Control Directions

❏

1. Turn on the transmitter and receiver and center the

trims. If necessary, remove the servo arms from the servos

and reposition them so they are centered. Reinstall the

screws that hold on the servo arms.

❏

2. With the transmitter and receiver still on, check all the

control surfaces to see if they are centered. If necessary, adjust

the clevises on the pushrods to center the control surfaces.

4-CHANNEL RADIO SET UP

(STANDARD MODE 2)

RUDDER

MOVES

RIGHT

FULL

THROTTLE

❏

3. Make certain that the control surfaces and the throttle

respond in the correct direction as shown in the diagram.

If any of the controls respond in the wrong direction, use

the servo reversing in the transmitter to reverse the servos

connected to those controls. Be certain the control surfaces

have remained centered. Adjust if necessary.

RIGHT AILERON

MOVES UP

LEFT AILERON

MOVES DOWN

ELEVATOR

MOVES DOWN

Set the Control Throws

To ensure a successful first flight, set up your Yak-55M EP

according to the control throws specified in the manual.

The throws have been determined through actual flight

testing and accurate record keeping, allowing the model

to perform in the manner in which it was intended. If, after

you have become accustomed to the way the Yak-55M

flies, you would like to change the throws to suit your flying

style, that is fine. However, too much control throw could

make the model too responsive and difficult to control, so

remember, "more is not always better."

❏

1. Use a box or something similar to prop up the bottom of

the fuselage so the horizontal stabilizer and wing will set level.

❏

2. Measure the 3D elevator throw first. Hold a ruler

vertically on your workbench against the widest part

(front to back) of the trailing edge of the elevator. Note the

measurement on the ruler.

These are the recommended control surface throws:

3D RATE

Down

1-7/8"

ELEVATOR

[48mm]

34°

Right

2-1/2"

RUDDER

[64mm]

29°

Down

1-3/4"

AILERONS

[44mm]

28°

HIGH RATE

Down

5/8"

5/16"

[16mm]

[8mm]

34°

11°

Left

Right

Left

Right

2-1/8"

1-3/4"

[54mm]

[44mm]

29°

25°

Down

3/4"

[19mm]

[13mm]

28°

12°

LOW RATE

Down

5/16"

[8mm]

5°

Left

1-3/4"

[44mm]

20°

Down

1/2"

[13mm]

8°