AutomationDirect SureServo2 매뉴얼 - 페이지 2

{카테고리_이름} AutomationDirect SureServo2에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. AutomationDirect SureServo2 18 페이지. 110/220 vac drives
AutomationDirect SureServo2에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (4 페이지)

AutomationDirect SureServo2 매뉴얼
Chapter 2: Installation
SureServo2™ Installation
Please follow the instructions in this chapter during installation. This chapter includes
information about the circuit breaker, fuse, EMI filter selection, and the regenerative resistor.
For drive dimensions and mounting holes, please see Appendix A.

Safety Precautions

If the connection between the servo drive and servo motor is over 20 meters, please increase
the gauge of the UVW connecting wire and the encoder cable. Please refer to Section 3.2.3 for
the wire specification.
2.1 - Ambient Storage Conditions
Before installation, this product must be kept in the shipping carton. In order to retain the
warranty coverage and for maintenance, please follow the instructions below for storage.
While the product is temporarily not in use:
• Store the product in an ambient temperature range of -20°C to +65°C�
• Store the product in a relative humidity range of 0% to 90% and a non-condensing
environment�
• Avoid storing the product in an environment containing corrosive gas�
2.2 - Ambient Installation Conditions
W
: T
arning
he servo drive insTallaTion locaTion should be free of devices ThaT generaTe
excessive heaT
airborne dusT and meTal parTicles
W
: T
arning
he ambienT TemperaTure for The moTor locaTion should be beTween
T
he insTallaTion locaTion should be free of heaT
,
oily dusT
corrosive and inflammable gas and liquids
The ambient temperature for the servo drive should be between 0°C and 55°C. If the
temperature is over 45°C, please place the product in a well-ventilated environment. During
long-term operation, the ambient temperature should be under 45°C to ensure the servo
drive's performance. If the product is installed in an electric box, make sure the servo drive
is vertically mounted with a fan installed on the box. For SV2A-2040, keep a clearance of at
least 10mm above the drives and keep the air flow above 0.5 m/s. For SV2A-2075, SV2A-2150,
SV2A-2200, SV2A-2300, SV2A-2550, SV2A-2750, and SV2A-2F00, keep the speed of air flow
above 1 m/s. Allow 5 cm of clearance beneath and on both sides of the servo drive. Its
temperature must be kept under 55°C and it must be kept clear of heat sources. Ensure the
size of the electric box and ventilation to prevent overheating and endangering the internal
electronics of the device. In addition, check if the machine's vibration affects the electrical
devices in the electric box.
Page 2–2
,
,
,
waTer
vapor
dusT and oily dusT
,
or vibraTion and elecTronic inTerference
,
corrosive and inflammable gas and liquids
-
generaTing devices
,
airborne dusT and meTal parTicles
I output (%) is the current output in percent
Ta (°C) is the operation temperature
Note: The maximum operation temperature of
models of 750W (or above) is 60°C, but the output
current is reduced as shown in the figure above;
the maximum operation temperature for models of
400W (or below) is 55°C.
SureServo2 User Manual – 1st Edition – 05/20/2021
,
.
0°c
40°c.
and
,
,
,
waTer
vapor
dusT and
.