ADEMCO 5808LSTA 설치 지침 - 페이지 2

{카테고리_이름} ADEMCO 5808LSTA에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. ADEMCO 5808LSTA 4 페이지. Photoelectronic smoke/heat detector with built-in wireless transmitter

페이지 인쇄

5808LSTA Photoelectronic Smoke/Heat Detector with

Built-in Wireless Transmitter Installation Instructions

SPECIFICATIONS

Power Source:

Height:

Diameter:

Weight:

Operating Ambient Temperature Range: 0° to 38° C (32° to 100° F)

Operating Humidity Range:

Heat Sensor:

Low Temperature Sensor

Agency Listings:

Before installing detectors, please thoroughly read these installation

instructions and Manual I56-407, Guide for Proper Use of System Smoke

Detectors, which provides detailed information on detector spacing, place-

ment, zoning, wiring, and special applications. Copies of this manual are

available from ADEMCO.

NOTICE: This manual should be left with the owner/user of this equip-

ment.

IMPORTANT: This detector must be tested and maintained regularly fol-

lowing CAN/ULC S536 requirements. The detector should be cleaned at

least once a year.

GENERAL DESCRIPTION

The 5808LSTA photoelectronic smoke/heat detector with built-in wireless

transmitter is intended for use with wireless alarm systems that support

5800 series devices. Refer to control/communicator installation instructions

for compatibility. The 5808LSTA smoke/heat detector can be used with

5881 series (L, M, H) and 5881EH receivers for residential installations.

For commercial installations, the 5881EH receiver should be used. The

transmitter can send alarm, tamper, maintenance (when control panels

are equipped to process maintenance signals), and battery condition mes-

sages to the system's receiver. The maintenance signal fully complies

with the sensitivity test requirement specified in NFPA 72, 7-2.2. Refer to

the wireless system's instructions for the maximum number of transmitters

that can be supported.

The 5808LSTA will sound its built-in temporal horn when smoke acti-

vates the detector (also the LED also flashes rapidly), or when the air

temperature reaches 135° F (the LED flashes normally, about once every

40 seconds). A message is also sent to the wireless control panel and the

smoke detector's ID number is displayed at the console. The alarm mes-

sage is transmitted every 4 seconds until the smoke condition has cleared

and the detector has reset. After the horn stops, a RESTORE message is

transmitted to the control panel and the ID number can be cleared from

the panel. During normal and low battery conditions, the LED flashes

approximately once every 40 seconds. The built-in Drift Compensation

algorithm automatically maintains the sensitivity of the detector. Once the

detector reaches its limit of compensation, it transmits a maintenance

signal to the panel. In maintenance condition, the LED stops flashing.

BATTERY INSTALLATION AND REPLACEMENT

The 5808LSTA is powered by two 3-volt CR123A or DL123A Lithium bat-

teries (included). The detector checks for low batteries at least every 60

minutes. If a low battery is detected, the transmitter sends a low battery

message to the control panel, which beeps and displays the detector's

ID. Unit will send low battery signal to control when it detects low battery

below 5.1V. This condition will exist for a minimum of seven days, and

then the detector's horn will "chirp" about every 40 seconds. The batteries

AD300-00-00

Two 3-volt CR123A Lithium Batteries (included). (Replace with Duracell

DL123A, Sanyo CR123A, Panasonic CR123A or ADEMCO 466.)

2.05 inches (52 mm)

5.0 inches (127 mm) without adapter bracket

5.5 inches (140 mm) with adapter bracket

8.5 oz. (241 g) without batteries

5% to 95% Relative Humidity

57°C (135° F) Fixed Temperature Electronic Thermistors

7°C ± 3°C (44.6°F ± 5.4°F) for 3.5 ± 0.5 hrs

ULC, UL 268 – Commercial and Residential Installations

should be replaced BEFORE the chirps begin. BE SURE TO REPLACE

BOTH BATTERIES WITH FRESH ONES.

To replace batteries:

1. Remove the detector from its mounting plate by twisting the detector

counterclockwise. Remove batteries, and dispose properly.

2. Install two new 3-volt CR123A Lithium batteries in the battery com-

partment. Follow the polarity diagram inside the compartment.

3. Reinstall the smoke detector onto the mounting plate by turning the

detector clockwise.

4. Test the detector as described in the TESTING TRANSMITTER

SIGNAL section of this manual. The LED should flash about once

every 40 seconds to indicate normal operation. If the batteries are not

installed correctly, the smoke detector will not operate and the batter-

ies may be damaged. If the detector does not appear to be sending a

signal during any of the tests, check for correct battery installation.

Indicator Light

Pulsing: Normal/Thermal Alarm

Fast Blink: Smoke Alarm

None: Call for Service

Figure 1. 5808LSTA Wireless Smoke/ Heat Detector

PROGRAMMING

The smoke detector's ID must be enrolled in the control panel during

installation of the system. The 5808LST must be enrolled on loop 1 as an

input "Type 3" (supervised RF).

Both heat and smoke detection transmit as Loop 1. Maintenance signal

is transmitted as Loop 2, Low temperature is transmitted as Loop 3 and

tamper is transmitted as Loop 4. To take advantage of these value added

features, these loops can be assigned to individual zones on the 5800

series wireless compatible panel.

Test Switch

A78-2332-03

I56-2249-00

ADEMCO, Woodbridge, Ontario.