ADEMCO Quest 2260SN 설치 지침 - 페이지 3

{카테고리_이름} ADEMCO Quest 2260SN에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. ADEMCO Quest 2260SN 4 페이지. Microwave/pir polling loop motion sensor

페이지 인쇄

ADJUSTMENTS AND SELECTIONS

Microwave Sensitivity Control

Turn the potentiometer clockwise to increase sensitivity.

DIP Switch Settings

(use a small pointed tool to move the switch handle)

No. Position

Function and Explanation

Supervision Failure Mode

ON:

SUSPEND PIR: In case of microwave channel failure,

the unit becomes non-operational.

OFF (default): REVERT TO PIR: In case of microwave channel failure,

the unit reverts to the PIR only mode.

Fluorescent Filter Mode

ON:

50Hz FLTR: Digital fluorescent light filter set for 50Hz.

OFF (default): 60Hz FLTR: Digital fluorescent light filter set for 60Hz.

LED Enable/Disable

ON (default): ENABLE: LEDs are enabled.

OFF:

DISABLE: LEDs are disabled.

Microwave Operation Mode

ON (default): NORMAL: Microwave channel always on.

OFF:

CONDITIONAL: Microwave channel on only when PIR

activity is detected.

Signal Processing Mode

ON:

INTERMEDIATE: Use this setting in normal

environments.

OFF (default): STANDARD: Use this setting for maximum false alarm

immunity. This setting tolerates environmental

extremes and is the recommended setting.

Accu-Trak Environmental Test Mode

ON:

ENV TEST: Accu-Trak environmental test is enabled.

OFF (default): NORMAL: Accu-Trak environmental test is disabled.

LED INDICATIONS

(when LEDs are enabled)

MODE

LED INDICATIONS

Power Up

Red LED is ON for 30 seconds

Alarm

Red LED ON

Accu-Trak

Green LED flashes for microwave detection

Test Mode

Red LED flashes for PIR detection

Supervision

Red LED flashes for PIR failure once per 3 sec.

Failure

Green LED flashes for microwave failure once per 3 sec.

SERIAL No. ID

This unit does not utilize DIP switches to set its zone number (ID).

Each unit has a unique factory-assigned serial number which must

be entered into the control panel during the zone programming

procedure. Therefore, this motion sensor can be used only with a

control that supports serial number devices.

Note that this motion sensor's unique factory-assigned serial

number can be found on the bar code label on its PC board.

The motion sensor's serial number can be entered by one of the

following methods:

A. Downloading (Zone Definition screen of Compass software).

Recommended for large installations and installations where

foot traffic cannot be controlled.

B. Entering through the keypad at the "INPUT S/N" prompt

during manual zone programming (see Important note below).

C. Activating the detector twice while at the "INPUT S/N" prompt

during manual zone programming.

If entering manually, be sure that other polling loop sensors are not

activated so that they cannot send a signal to the control while this

motion sensor is being programmed (mask motion sensors, don't

open/close doors, etc.).

IMPORTANT

To be sure that other polling loop devices are not activated when

entering serial numbers manually, power the system down,

disconnect the polling loop at the control, power back up again, and

immediately enter the program mode. Then proceed to Step 1 in the

following section. Remember to reconnect the polling loop when

programming is complete, powering the system down first.

To enter the unit's serial number

1. Using the control panel's keypad, enter Zone Programming mode.

2. Enter the Zone number, Zone Type, and other zone information for

the motion sensor, pressing [∗] to advance from prompt to prompt.

3. At the "Input Type" prompt, enter "6" for SL (Serial Polling Device)

and press [∗].

4. At the "INPUT S/N" prompt, either enter the serial number manually

(and a "1" for the loop number), or fault the motion sensor (the keypad

will "beep" to confirm signal), then wait 3-6 seconds and fault the

motion sensor again (the keypad should beep again to confirm). The

motion sensor should now be enrolled. A "1" should appear under the

"L" on the zone summary screen. If it does not, press [∗] and enter the

loop number manually at the next screen.

5. Press [∗] to continue programming other devices, or enter "00" to quit.

For detailed information, refer to the Zone Programming section in the

control panel's Installation Instructions.

TAMPER

Removal of the cover causes a front cover tamper switch to open.

Removal of the detector from the wall causes the back tamper switch to

open (if back case is tampered using a screw through the tamper hole;

see Figure 2). The control panel is automatically notified via the polling

loop when either of these events occur.

TEST PROCEDURES

On power-up, testing must not begin until the LED extinguishes after

first applying power to signify warm-up is complete, about 30 seconds. If

the LED begins to flash at a constant rate, refer to the section on

SUPERVISION.

Accu-Trak Environmental Test Mode

ADEMCO's unique Accu-Trak environmental test feature easily provides

an environmental check for potential false alarm sources on both the

PIR and microwave channels. Simply set DIP Switch #6 to ON.

Both microwave and PIR information are viewable simultaneously on

the two LEDs, providing crisp, immediate feedback (see below).

NOTE: When Accu-Trak environmental test mode is selected, an

alarm signal is reported to the control panel to prevent leaving

the detector in the test mode.

TEST

LED

PIR

RED

Microwave

GREEN

IMPORTANT:

Detection coverage can only be verified by walk-testing in the normal

operating mode (DIP Switch #6 set to OFF).

Testing in Normal Operating Mode

After testing with the unique Walk-Test mode, the detector should be

tested in the Normal Operating Mode with the following steps:

1. Remove the front cover and ensure that DIP Switch #6 is set to OFF

for Normal Operating Mode.

2. Set DIP Switch #5 to the Pulse Processing Option that will be used for

this installation.

3. Enable the LED by setting DIP Switch #3 ON.

4. Replace the front cover and walk through the protective zones,

observing that the detector's red LED lights whenever motion is

detected. If necessary, re-adjust the microwave sensitivity to the

minimum level required for satisfactory detection and repeat the

Walk Test.

5. After Walk-Testing is complete, the LED may be disabled, if desired

(DIP Switch #3 OFF).

– 3 –

ACCU-TRAK LED INDICATIONS

LED flashes when potential false alarm source is

detected, such as fans or heating duct.

LED is ON when potential false alarm source is

detected, such as a fan or mylar balloon.