Hifonics TMA2000.4 빠른 시작 설치 매뉴얼 - 페이지 2

{카테고리_이름} Hifonics TMA2000.4에 대한 빠른 시작 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Hifonics TMA2000.4 2 페이지.

Hifonics TMA2000.4 빠른 시작 설치 매뉴얼

Before you start

CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
Power cable size
Model
and fusing
It is critical to use the proper power
and ground cable. Select the size
listed here for your amplifier model.
Always use high quality copper
TMA- 400.4
cable. Visit our website for multi amp
TMA-800.5
MAXI 50A x 2
system cable recommendations.
TMA-1000.6
MAXI 70A x 1
TMA-2000.4
Be sure to use the proper fuse size
for each model. Some models require
an external fuse.
Installation
Disconnect
1
negative battery
terminal
Place terminal in a secure
position so that it won't
accidentally contact the
negative battery post
Run Cables
2
Properly route power,
speaker and RCA cables
through the vehicle.
Mount Amplifier
3
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplifier to
a secure surface. Do not mount
the amplifier upside down.
Chassis Ground
4
The chassis ground connection
is critical to the performance
of the amplifier. Choose a
location that is close to the
amplifier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Negative Power
5
Fuse Size
Cable Size
Connection
Attach the chassis ground
cable to the amplifier
25A x 2
negative terminal. It is
4ga
important to make sure this
connection is very tight.
40A x 2
Remote Turn-on
6
Connection
Attach the remote turn on
wire to the amplifier remote
output of the source unit.
Positive Power
7
Connection
Attach the main power cable
to the amplifier +12V. The
cable must run directly to
the battery and be properly
fused and be very tight.
Signal Input
8
Connection
Connect the RCA cables to
the INPUT connectors. The
OUTPUT can be used to
provide input for a second
amplifier.
Level Control
9
Bare metal
BRIDGED
LEFT
RIGHT
SPEAKER
OUTPUT
BRIDGED
BRIDGED
BRIDGED
LEFT
RIGHT
LEFT
RIGHT
CH 3
CH 4
SPEAKER
OUTPUT
SPEAKER
SPEAKER
OUTPUT
SPEAKER
OUTPUT
BRIDGED
BRIDGED
LEFT
RIGHT
CH 1
CH 2
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
BRIDGED
CH 3
CH 4
SPEAKER
OUTPUT
Turn the LEVEL control completely
INPUT
INPUT
SUBSONIC
counter-clockwise to minimum.
LEVEL
LEVEL
9V
0.2V
6V
0.2V
15
35Hz
PHASE
LPF
LPF
Find out more about performance marine electronics and navigation we have.
Speaker
10
BRIDGED
BRIDGED
Connections
LEFT
RIGHT
CH 3
Connect the speaker cables to
the speaker output connectors.
SPEAKER
OUTPUT
SPEAKER
Follow the diagram below
that best fits your speaker
configuration.
Stereo
Bridged
BRIDGED
BRIDGED
LEFT
RIGHT
CH 1
BRIDGED
CH 3
CH 4
SPEAKER
OUTPUT
SPEAKER
SPEAKER
OUTPUT
SPEAKER
OUTPUT
BRIDGED
CH 3
Monoblock
Monoblock
single woofer
BRIDGED
CH 1
CH 2
SPEAKER
SPEAKER
OUTPUT
SPEAKER
OUTPUT
OUTPUT
SPEAKER
OUTPUT
BRIDGED
CH 3
CH 4
Positive Battery
11
Connection
SPEAKER
OUTPUT
OUTPUT
SPEAKER
OUTPUT
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
Be prepared to disarm your vehicle's alarm and
to enter your radio / source unit code.
Re-connect
12
Negative Battery
Terminal
MODE
XOVER
Re-connect the negative
SUBSONIC
battery terminal making sure it
is securely tightened.
MONO STEREO
FULL
HP
LP
10
40Hz
XOVER
MODE
LPF
CH 4
SPEAKER
OUTPUT
OUTPUT
BRIDGED
BRIDGE
CH 2
LEFT
RIGHT
CH 3
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
SPEAKER
OUTPUT
BRIDGED
BRIDGE
CH 4
LEFT
RIGHT
CH 1
multiple woofers
BRIDGED
LEFT
RIGHT
OUTPUT
SPEAKER
OUTPUT
SPEAKER
SPEAKER
OUTPUT
SPEAKER
OUTPUT
BRIDGE
CH 3
SPEAKER
SPEAKER
OUTPUT
SPEAKER
OUTPUT