DynaQuip WaterCop ACA100 사용 설명서 및 설치 설명서 - 페이지 4
{카테고리_이름} DynaQuip WaterCop ACA100에 대한 사용 설명서 및 설치 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. DynaQuip WaterCop ACA100 16 페이지.
페이지 인쇄
Hardwired Sensor Probes: 10' white cord with single sensor probe . WaterCop® Pro sensor
probes are easily secured to the surface using adhesive or the mounting holes . Hardwired sensors
provide the same feedback to the Water Control Panel as the WaterCop® Pro wireless sensors .
Use hardwired sensor probes for convenience, or if conditions prevent wireless communication .
To extend sensor cords past the 10' they come with, please contact us for the proper wire
and method.
Lead-Free Brass Valve: Full port, NSF/ANSI 372 approved, lead-free, brass,
125 psi cold water, designed for placement on incoming water main .
Wireless Sensor: Power the Multisense Hub using 2 AAA alkaline batteries
or optional AC/DC power converter (sold separately) . Batteries will
provide backup power to sensors upon loss of electricity . Wireless sensors
areaddressable and supervised for conditions suchas water detection, sensor
short/open, and low/dead battery . 10' sensor probe cord allows for optimal
sensor placement . Wireless sensors can support 1 or 2 probes, ropes and/or
pressure sensor accessories plus has on-board ambient temperature
sensing (see pages 9–10) . Each Water Control Panel can support up
to 45 wireless sensors .
Range Enhancing Repeater: Enhances the transmission range of the wireless
sensors . Plugs into any standard wall outlet . Receives and re-transmits sensor
signals from outlying sensors to WaterCop® Pro Water Control Panel .
CAUTION!
It is strongly recommended that eye protection
be worn while servicing the system. Failure to
do so could result in personal injury. DO NOT
USE EXTENSION CORDS. KEEP FINGERS AND
OBJECTS AWAY FROM THE VALVE.
How the System Works
Leak sensors constantly monitor their selected areas for accumulating moisture . When a leak is
detected, a sensor will send a radio frequency signal (RF) to the WaterCop® Pro Water Control
Panel, instructing it to close the Brass Valve, shutting off the water supply to the property . The
WaterCop® Pro Valve will remain closed until it is reset manually or through the Water Control
Panel . After the WaterCop® Pro valve closes, the Control Panel will still receive ALERT and ALARM
signals from sensors and send notification if those outputs are used . The wireless sensors are
battery powered devices, enabling them to be located anywhere a leak is likely to occur, or where
water might cause damage . The WaterCop® Pro Actuator is powered through the Water Control
Panel, which requires household electrical power (common 115 VAC, grounded outlet) and will
not operate during a power outage unless receiving auxiliary power from a backup device such
as an Uninterruptible Power Supply unit (UPS) . Additionally, the use of a certified surge protection
device is highly recommended .
Operating the WaterCop® Pro
The normal position of the valve is open to allow full flow throughout the plumbing system . The
manual override handle on the top of the WaterCop® Pro Actuator will show the position of the
valve (in-line with the pipe means the valve is open; when the handle is not in-line it is not fully
open; when it is perpendicular to the pipe, the valve is fully closed) . W hen leaking water comes
4
GENERAL SAFETY
INFORMATION
Do not apply electrical power to the unit unless
the unit is fully assembled. Failure to do so could
result in personal injury and/or damage to the
unit. Disconnect power source before working on
or servicing the unit. Failure to do so could result
in personal injury.
Multisense Hub
MULTISENSE
HUB
Range
Enhancing
Repeater