HIKVISION CT-AC303-MB-3-6mm 사용자 설명서 - 페이지 2
{카테고리_이름} HIKVISION CT-AC303-MB-3-6mm에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. HIKVISION CT-AC303-MB-3-6mm 2 페이지.
페이지 인쇄3.Route the cables to the cable hole and connect
the corresponding power cable and video cable.
4.Fix the camera to the ceiling with the supplied
screws.
Figure 2-2 Fix the Camera to the Ceiling
5.Adjust the surveillance angle.
1).Loosen No.3 adjusting screw to adjust the
panning position 0 ~ 360 .
( °
° )
.
2).Tighten No.3 adjusting screw
3).Loosen the No.2 adjusting screw to adjust the
( °
° ) .
tilting position 0 ~ 90
4).Tighten No.2 adjusting screw.
5).Loosen No.1 adjusting screw to adjust the
( °
° ) .
azimuth angle of the image 0 ~ 360
.
6).Tighten No.1 adjusting screw
Figure 2-3 3-axis Adjustment
2.2 Wall Mounting for Type /III
II
Camera
Steps:
1.Drill the screw holes and the cable hole in the
ceiling according to the supplied drill template.
2.Hammer the supplied plastic expansion bolt into
the screw holes.
2
Ceiling Mounting
1
1
2
2
No.2 Screw Hole
No.1 Screw Hole
for Bracket
for Mounting
Base
1
1
2
Figure 2-4 Drill Template
3.Route the cables to the cable hole and connect
the corresponding power cable and video cable.
4.Fix the camera to the ceiling with the supplied
screws.
Adjusting Screw
Figure 2-5 Fix the Camera to the Wall
5. Adjust the surveillance angle.
1). Loosen No.3 adjusting screw to adjust the pan
°
°
position (0 ~ 360 ).
2).Tighten No.3 adjusting screw.
3). Loosen No.2 adjusting screw to adjust the
°
°
tilting position(0 ~ 90 ).
4).Tighten No.2 adjusting screw.
5). Loosen No.1 adjusting screw to adjust the
( °
° )
rotation position 0 ~ 360 .
6).Tighten No.1 adjusting screw.
360°
3
90°
2
360°
1
Figure 2-6 3-axis Adjustment
3 Menu Operation
Menu
VIDEO.
SETUP
LAUGUAGE
OUT
SPECIAL
ADJUST
SCENE
LENS
EXPOSURE
BACKLIGHT
WB
DAY&NIGHT
NR
CAM
INDOOR
MANUAL
SHUTTER
BLC
ATW
COLOR
2D NR
SHARPNESS
TITLE
OUTDOOR
AGC
HSBLC
AWC-SET
B/W
3D NR
D-EFFECT
MONITOR
INDOOR1
SENS-UP
INDOOR
EXT
MOTION
LSC
LOW-
BRIGHTNESS
OUTDOOR
PRIVACY
LIGHT
D-WDR
MANUAL
DEFECT
DEFOG
VERSION
Figure 3-1 Main Menu
l
A coaxial camera controller (purchase separately)
is required to select the menu and adjust the
camera parameters.
l
Cameras with a 720p resolution of these three
types do not support menu operation.
3.1 VIDEO.OUT
PAL or NTSC is selectable .
3.2 LANGUAGE
English, Japanese, CHN1, CHN2, Korean, German,
French, Italian, Spanish, Polish, etc., are selectable.
3.3SETUP
3.3.1 SCENE
You can select indoor, outdoor, indoor 1 and low
-light as the working environments.
3.3.2 LENS
The camera is equipped with a fixed lens.
3.3.3 EXPOSURE
SHUTTER: AUTO,1/25, 1/50, FLK, 1/200, 1/400,
1/1k, 1/2k, 1/5k, 1/10k, 1/50k, x2, x4, x6, x8, x10,
and x15 are selectable.
AGC
: You can set the AGC value from 0 to 15.
SENS-UP
: You can set the SENS-UP to OFF or AUTO.
BRIGHTNESS
: You can set the brightness value
from 1 to 100.
D-WDR
: You can set the D-WDR to ON to improve
the image quality or OFF to disable the function.
DEFOG
: You can set the defog function as ON to
enable the function. Position, size, and the defog
gradation are configurable.
EXPOSURE
1. SHUTTER
AUTO
1. SELECT
2. AGC
OFF
2. DISPLAY
3. LEVEL
3. SENS-UP
---
4. MODE
4. BRIGHTNESS
---|------ 40
5. BLACK MASK
5. DEFOG
OFF
6. DEFAULT
6. BACKLIGHT
OFF
7. RETURN
7. RETURN
RET
Figure 3-3 HSBLC
Figure 3-2 Exposure
3.3.4 Backlight
Backlight Compensation (BLC):
-GAIN:
Set the gain of BLC as High, Middle, or Low.
-AREA:
Press the up/down/left/right button to
define the BLC position and size. Select RET or
AGAIN to go back the BLC menu or re-define the
BLC area.
-Default:
Restore the BLC settings to the default.
HSBLC: Select an HSBLC area. Set the DISPLAY
status as ON. Press the up/down/left/right button
RESET
to define the area position and size. Set the HSBLC
EXIT
LEVEL from 0 to 100. Select ALL DAY or Night for the
HSBLC mode. Set the BLACK MASK status as ON or
OFF.
3.3.5 White Balance (WB)
INDOOR, OUTDOOR, MANUAL, ATW (Auto-tracking
White Balance), AWC→SET are selectable.
3.3.6 Day & Night
Color, B/W, and EXT are selectable for DAY and
NIGHT switches.
3.3.7 NR
2D NR
: You can set 2D NR status as ON or OFF.
3D NR
: Set the Smart NR status as ON and adjust
the 3D smart NR sensitivity ranges from 0 to 100.
Set the 3D NR LEVEL ranges from 0 to 100. Set the
START. AGC level as the threshold to enable AGC,
and set the END. AGC level as the threshold to
disable AGC.
2D&3D NR
1. 2DNR
OFF
8
2. 3DNR
ON
3. RETURN RET
Figure 3-5 NR
3.3.8 SPECIAL
Camera Title:
Edit the camera title on this section.
D-effect:
-FREEZE:
Set the freeze function as ON or OFF.
-MIRROR:
OFF, MIRROR, V-FLIP, and ROTATE are
selectable for mirror.
-D-ZOOM:
Define the zoom area by configuring
the position from PAN & TILT.
-SMART D-ZOOM:
The D-Zoom area, sensitivity
and time are configurable.
-NEG.IMAGE:
Set the NEG IMAGE as ON or OFF.
SPECIAL
8
1. CAM TITLE
ON
8
2. D-DFFECT
3. MOTION
OFF
4. PRIVACY
OFF
8
5. LANGUAGE
ENG
8
6. DEFECT
7. VERSION
130722
HSBLC
8. RETURN
RET
AREA 1
Figure 3-7 Special
ON 8
---|------ 40
Motion: Select a MOTION area. Set the DISPLAY
ALL DAY
ON
status as ON or OFF. Press the up/down/left/right
8
button to define the position and size of the area.
RET
Set the SENSITIVITY from 0 to 60. Set the MOTION
VIEW status as ON or OFF.
Privacy: Select a PRIVACY area. Set the DISPLAY
status as INV, MOSAIC, COLOR or OFF. Press the
up/down/left/right button to define the position
and size of the area.
Defect: LIVE DPC, STATIC DPC and Black DPC are
adjustable in this section.
Version
: You can check the software version of the
device.
PRIVACY
1. SELECT
AREA 1
8
2. DISPLAY
MOSAIC
3. COLOR
10
4. TRANS.
1
8
5. DEFAULT
6. RETURN
RET
Figure 3-9 Privacy Mask
3.3.9 ADJUST
Sharpness
: Adjust the sharpness from 0 to 15.
Monitor
: Monitor CRT, and Monitor LCD are
selectable.
LSC
: Set the LSC status as ON or OFF.
3.3.10 RESET
Reset all the settings to the default.
3.3.11 EXIT
Press OK to exit the menu.
3D NR
8
1. SMART NR
ON
2. LEVEL
------|--8 0
3. START. AGC -|--------10
4. END. AGC
-|--------10
5. RETURN
RET
Figure 3-6 3D NR
MOTION
1. SELECT
AREA 1
2. DISPLAY
ON8
3. SENSITIVITY
----|---- 30
4. MOTION VIEW ON
8
5. DEFAULT
6. RETURN
RET
Figure 3-8 Motion Detection
ADJUST
--------|15
1. SHARPNESS
2. MONITOR
LCD8
3. LSC
OFF
4. VIDEO. OUT
PAL
5. RETURN
RET
Figure 3-10 Adjust