Garmin nuvi 500-Series 소유자 매뉴얼 - 페이지 43

{카테고리_이름} Garmin nuvi 500-Series에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin nuvi 500-Series 50 페이지. Flush mount template
Garmin nuvi 500-Series에 대해서도 마찬가지입니다: 빠른 참조 매뉴얼 (2 페이지), 사용자 설명서 (28 페이지), 소유자 매뉴얼 (38 페이지), 중요 정보 (1 페이지), 소유자 매뉴얼 (44 페이지), 설치 지침 매뉴얼 (6 페이지)

페이지 인쇄

You can set the parameters the chartplotter uses when

calculating an Auto Guidance path.

Preferred Depth: Sets the minimum water depth, based on

chart depth data, that your boat can safely travel over.

NOTE: The minimum water depth for the premium charts

(made before 2016) is 3 feet. If you enter a value of less than

3 feet, the charts only use depths of 3 feet for Auto Guidance

path calculations.

Vertical Clearance: Sets the minimum height of a bridge or

obstacle, based on chart data, that your boat can safely

travel under.

Shoreline Distance: Sets how close to the shore you want the

Auto Guidance path to be placed. The Auto Guidance path

may move if you change this setting while navigating. The

available values for this setting are relative, not absolute. To

ensure that the Auto Guidance line is placed the appropriate

distance from shore, you can assess the placement of the

Auto Guidance path using one or more familiar destinations

that require navigation through a narrow waterway

the Distance from Shore, page

Adjusting the Distance from Shore

The Shoreline Distance setting indicates how close to the shore

you want the Auto Guidance line to be placed. The Auto

Guidance line may move if you change this setting while

navigating. The available values for the Shoreline Distance

setting are relative, not absolute. To ensure the Auto Guidance

line is placed the appropriate distance from shore, you can

assess the placement of the Auto Guidance line using one or

more familiar destinations that require navigation through a

narrow waterway.

Dock your vessel or drop the anchor.

Select Settings > Navigation > Auto Guidance > Shoreline

Distance > Normal.

Select a destination that you have navigated to previously.

Select Navigate To > Auto Guidance.

Review the placement of the Auto Guidance line, and

determine whether the line safely avoids known obstacles

and the turns enable efficient travel.

Select an option:

• If the placement of the Auto Guidance line is satisfactory,

select Menu > Stop Navigation, and proceed to step 10.

• If the Auto Guidance line is too close to known obstacles,

select Settings > Navigation > Auto Guidance >

Shoreline Distance > Far.

• If the turns in the Auto Guidance line are too wide, select

Settings > Navigation > Auto Guidance > Shoreline

Distance > Near.

If you selected Near or Far in step 6, review the placement of

the Auto Guidance line, and determine whether the line

safely avoids known obstacles and the turns enable efficient

travel.

Auto Guidance maintains a wide clearance from obstacles in

open water, even if you set the Shoreline Distance setting to

Near or Nearest. As a result, the chartplotter may not

reposition the Auto Guidance line, unless the destination

selected requires navigation through a narrow waterway.

Select an option:

• If the placement of the Auto Guidance line is satisfactory,

select Menu > Stop Navigation, and proceed to step 10.

• If the Auto Guidance line is too close to known obstacles,

select Settings > Navigation > Auto Guidance >

Shoreline Distance > Farthest.

• If the turns in the Auto Guidance line are too wide, select

Settings > Navigation > Auto Guidance > Shoreline

Distance > Nearest.

Chartplotter Data Management

(Adjusting

13).

If you selected Nearest or Farthest in step 8, review the

placement of the Auto Guidance line, and determine

whether the line safely avoids known obstacles and the turns

enable efficient travel.

Auto Guidance maintains a wide clearance from obstacles in

open water, even if you set the Shoreline Distance setting to

Near or Nearest. As a result, the chartplotter may not

reposition the Auto Guidance line, unless the destination

selected requires navigation through a narrow waterway.

Repeat steps 3 through 9 at least once more, using a

different destination each time, until you are familiar with the

functionality of the Shoreline Distance setting.

Other Vessel Settings

When your compatible chartplotter is connected to an AIS

device or VHF radio, you can set up how other vessels are

displayed on the chartplotter.

Select Settings > Other Vessels.

AIS: Enables and disables AIS signal reception.

DSC: Enables and disables digital selective calling (DSC).

AIS Alarm: Sets the collision alarm

Collision Alarm, page 7

Alerts, page

7).

Restoring the Original Chartplotter Factory

Settings

NOTE: This procedure deletes all settings information you have

entered.

Select Settings > System > System Information > Factory

Settings.

Chartplotter Data Management

Copying Waypoints, Routes, and Tracks

from HomePort to a Chartplotter

Before you can copy data to the chartplotter, you must have the

latest version of the HomePort software program loaded on your

computer and a memory card installed in the chartplotter.

Copy the data from HomePort to the prepared memory card.

For more information, see the HomePort help file.

Selecting a File Type for Third-Party

Waypoints and Routes

You can import and export waypoints and routes from third-party

devices.

Select Nav Info > Nav Info > Data Transfer > File Type.

Select GPX.

To transfer data with Garmin devices again, select the ADM file

type.

Copying Data from a Memory Card

Insert a memory card into a card slot.

Select Nav Info > Manage Data > Data Transfer.

If necessary, select the memory card to copy data to.

Select an option:

• To transfer data from the memory card to the chartplotter

and combine it with existing user data, select Merge from

Card.

• To transfer data from the memory card to the chartplotter

and overwrite existing user data, select Replace from

Card.

Select the file name.

(Setting the Safe-Zone

and

Enabling AIS Transmission Test