Garmin GPSMAP 4208 - Marine GPS Receiver 설치 지침 매뉴얼 - 페이지 2

{카테고리_이름} Garmin GPSMAP 4208 - Marine GPS Receiver에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 4208 - Marine GPS Receiver 19 페이지. Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
Garmin GPSMAP 4208 - Marine GPS Receiver에 대해서도 마찬가지입니다: 중요 안전 정보 (4 페이지), 중요 정보 (2 페이지), 소유자 매뉴얼 (2 페이지), 기술 참조 (30 페이지), 설치 지침 매뉴얼 (25 페이지), 설치 지침 매뉴얼 (25 페이지), 빠른 참조 매뉴얼 (2 페이지), 적합성 선언 (1 페이지), 보충 설명서 (24 페이지)

페이지 인쇄
Garmin GPSMAP 4208 - Marine GPS Receiver 설치 지침 매뉴얼
To install the bail mount and unit:
1. Using the bail mount as a template, mark the location of the four mounting holes. Be sure to leave at least 5" (12.7 cm) of clearance
behind the unit for the wiring.
NoTE: Mount a 4008/4208/5008/5208 unit 31
2. Using an appropriately sized drill bit, drill the pilot holes for your mounting hardware.
3. Secure the bail mount to the surface with your mounting hardware.
4. Loosely attach the mounting knobs to the GPSMAP 4000/5000 series unit.
5. Slide the unit onto the bail mount, and tighten the mounting knobs.
Flush Mounting the GPSMAP 4000/5000 Series Unit
Hardware (included):
• Flush mount template
• Four threaded 4 mm mounting studs
• Four 4 mm flat washers
• Four 4 mm lock washers
• Four 4 mm nuts
Tools required (not included):
• Jig saw
• Masking tape
• Scissors
• Drill
• Drill bits—
3
/
" (6 mm) and 4 mm
8
•
/
" (2 mm) Allen (Hex) wrench
1
16
• 4 mm sockets or wrenches
• Center punch and hammer
/
" (80 cm), and a 4012/4212/5012/5212 unit 39
1
4
GPSMAP
Pilot Hole
3/8" (9.5 mm)
6 17/32"
(165.90 mm)
Flush Mount Template Example (not to scale)
July 2007
190-00779-03_0B.indd 1
" from a magnetic compass to avoid interference.
/
3
8
4000 SerieS FluSh Mount teMPlAteS
®
GPSMAP 4008/4208
unit dimensions: 11 3/16" (284.4 mm) wide x 6 31/32" (176.9mm) high
Cut on
thiS line
9 5/8" (244.50 mm)
190-00779-03 Rev. B
GPSMAP 4000/5000 Series Installation Instructions
USE 4 mm DRILL BIT
Recommended clearance
for SD card door
1/2"
13 mm
Printed in Taiwan
7/9/2007 10:08:51 AM