Indesit K1G217S/RU 사용 설명서 - 페이지 22

{카테고리_이름} Indesit K1G217S/RU에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Indesit K1G217S/RU 28 페이지.
Indesit K1G217S/RU에 대해서도 마찬가지입니다: 사용 설명서 (40 페이지)

페이지 인쇄

Start-up and use

Using the hob

Lighting the burners

For each BURNER knob there is a complete ring

showing the strength of the flame for the relevant

burner.

To light one of the burners on the hob:

1. Bring a flame or gas lighter close to the burner.

2. Press the BURNER knob and turn it in an

anticlockwise direction so that it is pointing to the

maximum flame setting E.

3. Adjust the intensity of the flame to the desired

level by turning the BURNER knob in an

anticlockwise direction. This may be the minimum

setting C, the maximum setting E or any position

in between the two.

anticlockwise direction, towards the maximum flame

setting, until the burner is lit.

Several models are equipped with an ignition device

which is built into the knob; in this case the

electronic ignition device* is present ( see figure ) but

the ignition button is not. Simply press the BURNER

knob and turn it in an anticlockwise direction so that

it is pointing to the maximum flame setting, until the

burner is lit. The burner may be extinguished when

the knob is released. If this occurs, repeat the

operation, holding the knob down for a longer period

of time.

! If the flame is accidentally extinguished, switch off

the burner and wait for at least 1 minute before

attempting to relight it.

If the appliance is equipped with a flame failure

safety device (X), press and hold the BURNER knob

for approximately 2-3 seconds to keep the flame

alight and to activate the device.

To switch the burner off, turn the knob until it

reaches the stop position •.

Only available in certain models.

If the appliance is fitted with

an electronic lighting

device* ( C ), press the

ignition button, marked with

the symbol

, then hold

the BURNER knob down

and turn it in an

Practical advice on using the burners

For the burners to work in the most efficient way

possible and to save on the amount of gas

consumed, it is recommended that only pans that

have a lid and a flat base are used. They should also

be suited to the size of the burner.

Burner

ø Cookware diameter (cm)

Fast (R)

Semi Fast (S)

Auxiliary (A)

To identify the type of burner, please refer to the

diagrams contained in the "Burner and nozzle

specifications".

Using the oven

! The first time you use your appliance, heat the

empty oven with its door closed at its maximum

temperature for at least half an hour. Ensure that the

room is well ventilated before switching the oven off

and opening the oven door. The appliance may emit

a slightly unpleasant odour caused by protective

substances used during the manufacturing process

burning away.

! Before operating the product, remove all plastic

film from the sides of the appliance.

! Never put objects directly on the bottom of the

oven; this will avoid the enamel coating being

damaged. Only use position 1 in the oven when

cooking with the rotisserie spit.

Lighting the oven

To light the oven burner, bring

a flame or gas lighter close to

opening F ( see figure ) and

press the OVEN control knob

while turning it in an

anticlockwise direction until it

reaches the MAX position.

If, after 15 seconds, the burner is still not alight,

release the knob, open the oven door and wait for at

least 1 minute before trying to light it again.

! The oven is fitted with a safety device and it is

therefore necessary to hold the OVEN control knob

down for approximately 6 seconds.

24 - 26

16 - 20

10 - 14