Miller ArcReach SuitCase Non-CE 소유자 매뉴얼 - 페이지 17

{카테고리_이름} Miller ArcReach SuitCase Non-CE에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Miller ArcReach SuitCase Non-CE 48 페이지.

페이지 인쇄

Keep your head out of the fumes

�

Do not weld on drums or any closed containers.

Wear dry insulating gloves. Do not touch electrode (wire) with bare hand. Do not wear wet or damaged gloves.

Read Owner's Manual and inside labels for connection points and procedures.

Induction heating can cause injury or burns from hot items such as rings, watches, or parts.

Keep flammables away from welding. Do not weld near flammables.

Welding sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.

Do not cut on drums or any closed containers.

Complete Parts List is available at www.MillerWelds.com

Become trained and read the instructions before working on the

Welding sparks can cause fires. Have a fire extinguisher nearby, and

Welding sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.

machine or welding.

Cutting sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.

have a watchperson ready to use it.

Do not grip material near cutting path.

Become trained and read the instructions before working on the

machine or cutting.

Do not weld on drums or any closed containers.

Turn off power before disassembling torch.

Falling unit can cause injury and damage. Do not move unit where two wheels are at a different height and un

could tip

avoid tipping. Be careful when moving unit over uneven surfaces.

Remove unit from shipping crate. Remove Owner's Manual from unit.

Follow instructions to install muffler.

Writer: If necessary, replace the word "handle" with "lift eye'.

Do not cut on drums or any closed containers.

Writer: If necessary, replace the word "handle" with "lift eye'.

Do not stack racks. Lift only with proper equipment and correct procedures.

Do not remove or paint over (cover) the label.

Do not use one handle to lift or support unit.

Every 100 hours, check and clean filter and check condition of hoses.

Moving parts can injure.

Do not grip material near cutting path.

Drive rolls can injure fingers.

During the first 50 hours of operation keep welding load above 200

amperes. Do not weld below 200 amperes of output.

Always connect green, Or green with yellow stripe, wire to supply grounding terminal.

Turn off power before disassembling torch.

Welding wire and drive parts are at welding voltage during operation -

Welding wire and drive parts are at welding voltage during operation

Connect black, white, and red wires (L1, L2, L3) to line terminals.

keep hands and metal objects away.

After the first 50 hours of operation, change the engine oil and filter.

Pinch points can injure.

Become trained and read the instructions before working on the

Pinch points can injure.

Do not remove or paint over (cover) the label.

machine or welding.

Consult rating label for input power requirements.

Wear hat and safety glasses. Use ear protection and button shirt

Recycle.

Wear hat and safety glasses. Use ear protection and button shirt col-

collar. Use welding helmet with correct shade of filter. Wear complete

lar. Use welding helmet with correct shade of filter. Wear complete

body protection.

Become trained and read the instructions and labels before working on machine.

Become trained and read the instructions before working on machine.

Become trained and read the instructions before working on the

Become trained and read the instructions before working on the ma-

machine or welding.

chine or welding.

Connect Green Or Green/Yellow grounding conductor to ground terminal first.

Connect input conductors (L1, L2, L3) to line terminals.

Connect green or green/yellow grounding conductor to ground terminal.

Move jumper links as shown on inside label to match input voltage at

job site. Include extra length in grounding conductor and connect

grounding conductor first. Connect line input conductors as shown on

inside label. Double-check all connections, jumper link positions, and

input voltage before applying power.

Close door before turning on unit.

Read the Owner's Manual before working on this machine.

at job site. Double-check all connections, relinking board posi

input voltage before applying power.

For single phase operation, insulate and isolate red conductor

Include extra length in grounding conductor and connect grou

conductor first. Connect black, white, and red wires (L1, L2, L

line terminals.

keep hands and metal objects away.

Wear hat and safety glasses. Use ear protection and button s

collar. Use welding helmet with correct shade of filter. Wear co

body protection.

Connect input conductors (L1, L2 And L3) to line terminals.

Wear hat and safety glasses. Use ear protection and button s

collar. Use welding helmet with correct shade of filter. Wear co

body protection.

Become trained and read the instructions before working on th

machine or welding.

OM-278792 Page 11

Safe6

Safe7 2017 04

Safe1

Safe9

Safe

Safe6

Safe40 2012 05

Safe1

Safe

Safe9

Safe41 2012 05

Safe

Safe9

Safe46 2012 05

Safe

Safe2

Safe9

Safe3

Safe51 2012 05

Safe

Safe10

Safe

Safe54 2017 04

Safe

Safe10

Safe64 2017 04

Safe

Safe55 2012 05

Safe10

Safe2

Safe65 2012 06

Safe3

Safe57 2017 04

Safe10

Safe66 2012 06

Safe

Safe10

Safe65 2012 06

Safe67 2012 06

Safe

Safe3

Safe10

Safe74 2012 07

Safe68 2012 06

Safe3

Safe 10

OM-

Safe69 2012 06

Safe3

Safe70 2012 06

Safe4