HP 1810 series 빠른 사양 - 페이지 32
{카테고리_이름} HP 1810 series에 대한 빠른 사양을 온라인으로 검색하거나 PDF를 다운로드하세요. HP 1810 series 32 페이지. Smart-managed, fixed-configuration gigabit and fast ethernet layer 2 switches
HP 1810 series에 대해서도 마찬가지입니다: 사양 (32 페이지), 데이터시트 (11 페이지)
페이지 인쇄
QuickSpecs
Accessory Product Details
HP X121 1G SFP RJ45 T
Transceiver (J8177C)
HP X121 1G SFP RJ45 T
Transceiver: An SFP format
gigabit transceiver with
RJ45 connectors using
1000BaseT technology.
To learn more, visit:
www.hp.com/networking
© Copyright 2009-2014 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without
notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products
and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial
errors or omissions contained herein.
Notes
Services
Ports
Physical characteristics
Environment
Cabling
Notes
Services
DA - 13447 North America — Version 18 — January 17, 2014
A mode conditioning patch cord may be needed in some multimode fiber
installations.
Wavelength: 1310nm
Power Consumption: < 500mW Typical
Refer to the HP website at
www.hp.com/networking/services
service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local HP sales office.
1 RJ-45 1000BASE-T port (IEEE 802.3ab Type 1000BASE-T); Duplex: full only
Dimensions: 2.71(d) x 0.54(w) x 0.55(h) in. (6.88 x 1.37 x 1.4 cm)
Weight: 0.06 lb. (0.03 kg)
Operating temperature: 32°F to 158°F (0°C to 70°C); with 100 LFM airflow over
the SFP module)
Operating relative humidity: 0% to 95% @ 75°F (25°C), noncondensing
Nonoperating/Storage temperature: -40°F to 185°F (-40°C to 85°C)
Nonoperating/Storage relative humidity: 0% to 95% @ 77°F (25°C),
noncondensing
Altitude: up to 10,000 ft. (3000 km)
Cable type:
1000BASE-T: Category 5 (5E or better recommended), 100 Ù differential 4-pair
unshielded twisted pair (UTP) or shielded twisted pair (STP) balanced,
complying with IEEE 802.3ab 1000BASE-T;
Maximum distance:
• 100 m
Power consumption is nominally 1 watt.
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the J8177C 1000Base-T Mini-
GBIC" on the "ProCurve Mini-GBICs and SFPs" Manuals Web page.
The J8177C Gigabit copper mini-GBIC is not supported on dual-personality
ports.
The J8177C is capable of 100 Mb operation. This is supported on only the HP
ProCurve Switch 8200zl, 5400zl, and 6200yl Series using software version
K.12.21 or later. Use the "auto-100" port setting to enable 100 Mb operation.
Important: The earlier J8177B does not support 100 Mb operation.
When used in the ProCurve Switch gl 20-Port 10/100/1000 Module (J4908A),
the J8177C mini-GBIC can be installed in either the upper or lower mini-GBIC
port, but will block access to the other port.
Refer to the HP website at
www.hp.com/networking/services
service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local HP sales office.
HP 1810 Switch Series
for details on the
for details on the
Page 32