Axxess AXDIS-FD3 설치 지침 매뉴얼 - 페이지 4

{카테고리_이름} Axxess AXDIS-FD3에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Axxess AXDIS-FD3 16 페이지.

페이지 인쇄

CONNECTIONS

3.5mm jack steering wheel control retention:

• The 3.5mm jack is to be used to retain audio controls on the steering wheel.

For the radios listed below: Connect the 3.5mm adapter to the male 3.5mm SWC jack

•

from the AXDIS-FD3 harness. Any remaining wires tape off and disregard.

•

Eclipse: Connect the steering wheel control wire, normally Brown, to the Brown/

White wire of the connector. Then connect the remaining steering wheel control

wire, normally Brown/White, to the Brown wire of the connector .

•

Metra OE: Connect the steering wheel control Key 1 wire (Gray) to the Brown wire.

•

Kenwood or select JVC with a steering wheel control wire: Connect the Blue/Yellow

wire to the Brown wire.

Note: If your Kenwood radio auto detects as a JVC, manually set the radio type to

Kenwood. See the instructions under changing radio type.

•

XITE: Connect the steering wheel control SWC-2 wire from the radio to the Brown wire.

•

Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the AXSWCH-PAR (sold

separately), and then connect the 4-pin connector from the AXSWCH-PAR into the radio.

Note: The radio must be updated to rev. 2.1.4 or higher software.

•

Universal "2 or 3 wire" radio: Connect the steering wheel control wire, referred to

as Key-A or SWC-1, to the Brown wire of the connector. Then connect the remaining

steering wheel control wire, referred to as Key-B or SWC-2, to the Brown/White wire of

the connector. If the radio comes with a third wire for ground, disregard this wire

Note: After the interface has been programmed to the vehicle, refer to the

manual provided with the radio for assigning the SWC buttons. Contact the radio

manufacturer for more information.

• For all other radios: Connect the 3.5mm jack from the AXDIS-FD3 harness into the jack on

the aftermarket radio designated for an external steering wheel control interface. Please

refer to the aftermarket radios manual if in doubt as to where the 3.5mm jack connects.

(CONT)

INSTALLATION

With the key in the off position:

• Connect the 16-pin harness, and the AXDIS-FD3 harness, into the AXDIS-FD3 interface.

Attention! Do not connect the AXDIS-FD3 harness to the wiring harness in the vehicle just yet.

Attention! If retaining steering wheel controls, ensure that the jack/wire is connected to the radio before

proceeding. If this step is skipped, the interface will need to be reset for the steering wheel controls to function.

PROGRAMMING

STEERING WHEEL CONTROL SETTINGS

For the steps below, the L.E.D. located inside the interface can only be seen while active. The interface does not

need to be opened to see the L.E.D.

1. Start the vehicle.

2. Connect the AXDIS-FD3 harness to the wiring harness in the vehicle.

3. The L.E.D. will initially turn on solid Green, then turn off for a few seconds while it auto detects the radio

installed.

4. The L.E.D. will then flash Red up to (23) times indicating which radio is connected to the interface, and then

turn off for a couple of seconds. Pay close attention to how many Red flashes there are. This will help in

troubleshooting, if need be. Refer to the L.E.D. feedback section for more information.

5. After a couple seconds the L.E.D. will turn on solid Red while the interface auto detects the vehicle. The radio will

shut off at this point. This process should take 5 to 30 seconds.

6. Once the vehicle has been auto detected by the interface, the L.E.D. will turn on solid Green, and the radio will

come back on, indicating programming was successful.

7. Test all functions of the installation for proper operation, before reassembling the dash. If the interface fails to

function, refer to Troubleshooting section.

Note: The L.E.D. will turn on solid Green for a moment, and then turn off under normal operation after the

key has been cycled.