Siemens EH8 SC1 Series 사용 설명서 - 페이지 10

{카테고리_이름} Siemens EH8 SC1 Series에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Siemens EH8 SC1 Series 16 페이지.
Siemens EH8 SC1 Series에 대해서도 마찬가지입니다: 사용 설명서 (12 페이지)

페이지 인쇄

Time programming function

This function may be used in two different ways:

to automatically switch off a hotplate.

■

as a timer.

■

Turning off a hotplate automatically

Enter the cooking time for the required hotplate. The hotplate

turns off automatically once the time has elapsed.

How to program

Select the required power level.

Press the

symbol of the desired hotplate. The hotplate

display shows

‹‹

and the indicator

Select the required cooking time in the programming panel.

The possible previous setting is, from left to right 1, 2, 3, etc.,

up to 10 minutes. Within the next 10 seconds, continue

passing through the options in the programming panel until

reaching the desired time.

The cooking time will be displayed for 10 seconds then begin

to count down.

Automatic programming

If the previous setting from 1 to 5 is pressed in the

programming panel, the cooking time is reduced by one

minute, if it is held down the time is automatically reduced to

one minute.

If the previous setting from 6 to 10 is pressed in the

programming panel , the cooking time is increased by one

minute, if it is held down the time is automatically increased to

99 minutes.

Automatic time limitation

If the hotplate remains in use for a long time and no changes

are made in the settings, the automatic time limitation function

is triggered.

The hotplate stops heating. The

heat indicator

flash alternatively in the display.

•

The indicator goes out when any symbol is pressed. The

hotplate can now be reset.

When the automatic time function is used, it is governed by the

selected power level (from 1 to 10 hours).

comes on.

symbol and the residual

"‰

Once the time has elapsed

The hotplate switches off. The beep sounds and the display

comes on

for 10 seconds. The

‹‹

Pressing the

symbol turns off the indicators and stops the

beeping.

Changing or cancelling the time

Press the

symbol of the desired hotplate. Change the

cooking time in the programming panel, or set to

Note: Any cooking time can be programmed up to 99 minutes.

Automatic timer

With this function you may select a cooking time for all

hotplates. Once a hotplate is switched on, the selected time will

begin to count down. The hotplate will automatically switch off

when the cooking time has elapsed.

Instructions on activating the timer are found in the chapter

entitled "Basic settings".

Note: The cooking time of a hotplate may be cancelled or

changed:

Press the

symbol of the desired hotplate. Change the

cooking time in the programming panel, or set to

Timer

The timer can be set for periods of up to 99 minutes. It is

independent of the other settings. The hob must be switched

on. The timer can be set for any hotplate not turned on. This

function does not automatically switch off a hotplate.

How to program

Press the symbol

for the hotplate, the indicator

turned on.

lights up in the time program function display.

‹‹

Select the desired time in the programming panel.

The timer starts to count down after a few seconds.

Once the time has elapsed

A warning beep sounds. In the time program function display

‹‹

is shown, and the

indicator comes on. After 10 seconds

the indicators turn off.

Pressing the

symbol turns off the indicators and stops the

beep.

Changing or cancelling the time

Press the

symbol of the desired hotplate. Change the

cooking time in the programming panel, or set to

Note: When the timer is activated, the corresponding hotplate

is locked. First turn off the timer and then the hotplate.

indicator lights up.

‹‹