Sony NEX-VG30H 서비스 매뉴얼 - 페이지 20
{카테고리_이름} Sony NEX-VG30H에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Sony NEX-VG30H 32 페이지. Interchangeable lens digital hd video camera recorder
Sony NEX-VG30H에 대해서도 마찬가지입니다: 제한 보증 (1 페이지), 사양 (4 페이지)
페이지 인쇄
2-1-6. HANDLE BLOCK SECTION
ns: not supplied
253
254
#2
252
1
#12
BT6601
(Note 2)
ns
BH6601
(Note 2)
251
#46
#46
259
Ref. No.
Part No.
Description
251
A-1902-497-A
MS-1002 BOARD, COMPLETE
252
4-257-720-11
FRAME, MS
253
4-257-732-01
PANEL, BT UPPER
254
4-437-444-01
CABINET (456), GRIP (UPPER)
* 255
4-257-736-01
COVER, MIC
256
4-257-669-01
HANDLE
* 257
4-257-670-01
GUARD (H), FLEXIBLE
258
4-437-477-01
FRAME (456), GRIP
259
4-299-877-01
GASKET (MS)
260
1-490-451-11
SWITCH BLOCK, CONTROL (GZ45600
NEX-VG30/VG30E/VG30EH/VG30H_L2
255
#2
#198
(Note 1)
2
256
#2
260
258
#12
#12
#69
261
#69
Overall Section-3
(See Page 2-9)
#238
(Note 1)
: BT6601 (LITHIUM RECHARGEABLE BATTERY)
Board on the mount position.
(See page 6-50 of Level 3)
Ref. No.
Part No.
Description
261
4-437-478-01
CLAMP (PZ), FLEXIBLE
BH6601
1-251-928-21
SOCKET, BATTERY (Note 2)
BT6601 1-756-134-15
BATTERY, LITHIUM (SECONDARY) (Note 2)
#2
2-635-562-31
SCREW (M1.7)
#12
3-080-204-21
SCREW, TAPPING, P2
#46
2-660-401-11
SCREW (M1.7), NEW TRU-STAR, P2
#69
2-599-475-21
SCREW (M1.7)
#198
4-186-545-01
SCREW, 0+Z M1.7 SG (SPIN) (Note 1)
#238
4-287-436-01
SCREW (M1.7) (Note 1)
DISASSEMBLY
1. Remove in numerical order (
1
#12 X 3 → #46 X 1
1
Bottom View
#46
#198 X 1 → #2 X 3 → #12 X 1 → #238 X 1
257
2
Top View
#69
#2
Screw
#2: M1.7 X 4.0
#12: M1.7 X 5.0 (Tapping)
(Black)
(Black)
2-635-562-31
3-080-204-21
1.7
4.0
M1.7 X 3.5
#238:
(Black)
4-287-436-01
1.7
3.5
Note
Note 1: This screw cannot be reused. Discard the screw removed
once in servicing.
Instead, use a new screw.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Note 2: Replace the battery holder (BH6601) together when replacing
the lithium storage battery (BT6601) on the MS-1002 board.
(The battery holder removed once cannot be used again.)
When mounting these parts, mount new battery holder first
and attach new lithium storage battery next.
2-8
to
) in the left figure.
2
#12
#12
Bottom View
#198
#2
#46: M1.7 X 3.0
#69: M1.7 X 3.0
(Silver)
(Red)
2-660-401-11
2-599-475-21
1.7
1.7
5.0
3.0
Note 1: このねじは再利用することができません。
サービス対応時に一度でも外した場合は新品のねじと交換
してください。
電池の交換は，正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と交換して
ください。
使用済み電池は，取扱指示に従って処分してください。
Note 2: MS-1002基板のリチウム蓄電池 (BT6601) を交換する場合は
バッテリホルダ (BH6601) も同時に新品に交換してくださ
い。(一度使用したバッテリホルダは再使用できません。)
部品取り付けの際は，先にバッテリホルダを取り付けてか
らリチウム蓄電池を装着してください。
Left View
#12
#2
#238
#198: M1.7 X 4.0
(Silver)
4-186-545-01
1.7
1.7
3.0
4.0
注意