Cisco TelePresence 설치 매뉴얼 - 페이지 3

{카테고리_이름} Cisco TelePresence에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco TelePresence 4 페이지. Configuring a cisco unified communications manager sip trunk with a cisco telepresence content server
Cisco TelePresence에 대해서도 마찬가지입니다: 브로셔 (4 페이지), 사양 (7 페이지), 관리자 매뉴얼 (27 페이지), 빠른 참조 매뉴얼 (2 페이지), 매뉴얼 (24 페이지), 설치 시트 (2 페이지)

페이지 인쇄

Installing Cisco TelePresence System Profile 65" Presentation Unit

ThE PROFILE 65" PRESENTATION UNIT IS DELIvERED WITh:

Monitor

Column

Foot module (stand-alone or wall stand)

grille

Accessories box:

• Microphone

• Monitor cable

• Power cable (optional)

• Joint profile

• 8 × Screws M10x30 (Set screw)

• 2 × Screws M4x40, 2 × Screw M4x16

• 4 × Nut plates

• Tools

NOTE:

The Profile 65" Main system should be

installed before the Presentation unit.

Unpacking the unit

FOOT MODULE (25 kg / 55 LbS)

Open the snap lockers and lift out the foot module box.

Accessories to the foot module:

hEAvY

• Allen key, orange wrench for levelling adjustment, wall

CAUTION

brackets (wall stand only), spacer (wall stand only),

screws and bolts.

MAIN UNIT

Place the unit on a stable surface, open the snap lockers to

remove outer cover and locate the different parts:

• Monitor box, grille box, Accessories box, Column, Joint

hEAvY

profile.

CAUTION

Lift out the grille box and accessories box. Remove the

packaging above and around the column and monitor box.

Key lock and level adjustment

The level adjustment tool is found in the foot module box,

and the key lock tool is found in the accessories box.

KEY LOCK

Place the orange key on the key lock and turn

clockwise to lock, counter-clockwise to unlock.

LEvELLINg ADJUSTMENT

Place the orange level adjustment tool on the foot

wheel (under the foot plate). Seen from above,

turn clockwise to adjust the height up.

Use the opposite side of the tool and turn

counterclockwise to adjust the height down.

Presentation unit

Main system

Mounting the column to the foot module to complete the bottom module

PERSON 1:

Lift here.

PERSON 2:

Lift here.

Front

The illustration shows the stand-alone foot module. The

wall stand foot module is mounted in the same way.

Lock

Unlock

PRECAUTIONS

Follow the steps in this installation guide when unpacking

and assembling the Profile 65" Presentation unit.

This is the second part of the Profile 65" Dual system.

The main part is the Profile 65" system. For further

details see the Profile 65" Installation sheet.

A minimum of four (4) persons are required during the

installation of the system.

• The monitor box requires four (4) persons to lift.

• The column requires two (2) persons to lift.

• The foot module requires two (2) persons to lift.

NOTE:

The floor must be in level.

Lift the column and place it carefully on the foot module.

When looking down through the column you can see the four screws in the foot

module. Make sure the screws enter the corresponding holes in the column.

Open the front door to access the screws. Secure the column to the foot module

with four nuts. The nuts are found in the plastic bag. See the illustration below.

The illustration shows

a cross section of

the bottom module

(column and foot

module).

Fasten the 4 nuts

(two on each side

of the system).

Mounting the wall stand

(applies to wall stand option only)

The wall brackets, bracket spacer, Allen key and screws

are found in the foot module box.

WARNINg

Due to the size and mass of this equipment, it is very

important that the wall stand is safely installed according to

the installation instructions, and that the wall is able to safely

support the product.

It is highly recommended that the wall stand is installed by

trained personnel.

Choose the short or long bracket depending on the required

distance between the bottom module and the wall.

Place the spacer underneath the wall bracket and fasten

the bracket to the bottom module. Re-use the existing three

screws. Use the Allen key, found in the foot module box.

Place the bottom module by the wall, mark where to fasten

the bracket and move away the bottom module.

Add the suitable fixing device for the screws in the wall.

Place the bottom module by the wall and fasten it to the

wall.

Page 1

WEIghTS OF ThE DIFFERENT UNITS

DIMENSIONS (WhEN ASSEMBLED)

(PACKAgE INCLUDED)

The Profile 65" Dual system has the following

• Monitor box: 110 kg / 243 lbs

dimensions:

• Column: 40 kg / 88 lbs

• Foot module box: 25 kg / 55 lbs

• Accessories and grille boxes: 7 kg / 15 lbs

UNPACKINg ThE SYSTEM AT ThE DESTINATION

It is highly recommended to unpack and assemble the

Presentation unit at the place where it is to be used.

Check the dimensions of the lift if you need to use a lift

for the transportation.

USER DOCUMENTATION

Outer dimensions and total weight of the main unit

User guides and compliance and safety information for

(package included):

this product are available on the Cisco web site:

http://www.cisco.com/go/profile-docs

• Height: 145 cm / 57.1 in.

• Width: 76 cm / 29.9 in.

• Length: 170 cm / 66.9 in.

• Weight: 183 kg / 403 lbs

Removing the cable hatch covers

Both systems: Open the door and remove

the inner and outer cable hatch covers on

both the main system and the presentation

unit, using a 3 mm Allen key.

Main system

When mounting the systems together

(see step 6), the cables are lead through the cable hatches.

Long wall bracket

Choose the short or long bracket

depending on the required distance

between the bottom module and

Short wall bracket

the wall.

Use the spacer between the bottom

Spacer

module and the wall bracket.

• Height: 167 cm / 65.7 in.

• Width: 308 cm / 122 in.

• Depth:

• Stand-alone: 66 cm / 26 in.

• Wall stand, with short bracket: 44.7 cm / 17.6 in

• Wall stand, with long bracket: 52.2 cm / 20.6 in.

• Joint profile, width: 16 mm / 0.63 in.

Remove the

cable hatch

covers.

Presentation unit