Epson PowerLite 1725 제품 지원 게시판 - 페이지 30

{카테고리_이름} Epson PowerLite 1725에 대한 제품 지원 게시판을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson PowerLite 1725 34 페이지. Esc/vp21 command business projectors
Epson PowerLite 1725에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 운영 매뉴얼 (47 페이지), 부품 목록 (1 페이지), 빠른 설정 매뉴얼 (4 페이지), 사용자 설명서 (1 페이지), 제품 지원 게시판 (25 페이지), 제품 지원 게시판 (12 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지), 사양 (2 페이지), 사용자 설명서 (25 페이지)

S/N for projectors with the EasyMP V.1.10 firmware installed

Below are the starting serial numbers of units that ship with Firmware V.1.10. Pre-installed:

Model

Serial Number

NOTE: The EasyMP version of the PowerLite 1815p projectors is already V.1.10 for all

PowerLite 1815p projectors. Therefore the PowerLite 1815p projectors do not need the

V.1.10 firmware upgrade.

Download procedure

Download the firmware update file, epson12312.exe to the PC. This file is a self-extracting

archive and will decompress to C:\EPSON\epson12312_easymp_110. Copy the firmware

update files to the root directory of a USB Thumbdrive (flash memory).

Note: Make sure that the root directory of the flash memory only has the 2 firmware update

files on it; no other files or folders should exist on the USB memory device.

Note: Do not unplug the power cord or remove the USB device before the upgrade is

complete. If the firmware update procedure is interrupted for any reason, before the

procedure is complete, it may render the projector unusable. If this occurs you will need

to contact Epson or take your projector to an authorized Epson Customer Care Center.

1. Power on the projector.

2. Make sure that the projector is set to "Network Off" by clicking, Menu ->Extended ->

Standby Mode. If the Standby Mode is set to "Network ON", set it to "Network Off", and

turn the projector off and on.

NOTE: If you attempt to run the firmware upgrade with the projector set to "Network

On", then the projector will be stuck in a loop and will continue to run the update.

In this case, remove the USB flash memory at the moment that the green light of

USB access indicator goes off.

3. Display the EasyMP main screen by pushing EasyMP button on the remote control.

4. Connect the USB flash memory to USB port Type A on the projector. A Black screen is

displayed. The projector enters download mode while making the 3 LED indicators

(Power, Lamp and Temp indicators) show solid orange. After a while, the USB access

indicator lights green and the update will start. When the update is complete, the green

light of USB access indicator goes off. NOTES: USB access indicator lights green a few

seconds after Power, Lamp and Temp LED's show solid orange. Don't remove the USB

flash memory during the updating (USB access indicator is lit.)

PowerLite 1715c

JHZG730647F

PowerLite 1705c

JJKG730217F

Page 2 of 5

PSB.2007.06.002

PowerLite 1815p

JV2F730001L