Toshiba 24/32 WK3C Series 사용 설명서 - 페이지 35

{카테고리_이름} Toshiba 24/32 WK3C Series에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Toshiba 24/32 WK3C Series 50 페이지.

페이지 인쇄

• The location where the transmission is most effective

differs depending on the usage environment.

• The Wireless feature of the TV supports 802.11 a,b,g

& n type modems. It is highly recommended that

you should use the IEEE 802.11n communication

protocol in order to avoid any possible problems

while watching videos.

• You must change your modem's SSID when there

are any other modems around with the same SSID.

You can encounter connection problems otherwise.

Use a wired connection if you experience problems

with a wireless connection.

Configuring Wireless Device Settings

Open the Network menu and select Network Type as

Wireless Device to start connection process.

Highlight Scan Wireless Networks option and press

OK to start a search for available wireless networks.

All found networks will be listed. Highlight your desired

network from the list and press OK to connect. A

network with hidden SSID can not be detected by

other devices. If you want to connect to a network with

hidden SSID, scroll down the list of detected wireless

networks, highlight the Add New Network option and

press OK. Enter the name of the network and select

the security type using the related options to connect.

Note: If the modem supports N mode, you should set N

mode settings.

If the selected network is password-protected, enter

the correct key by using the virtual keyboard. You can

use this keyboard via the directional buttons and the

OK button on the remote control.

Wait until the IP address is shown on the screen.

This means that the connection is now established.

To disconnect from a wireless network, highlight

Network Type and press Left or Right buttons to set

as Disabled.

If you have connected to a wireless network Discon-

nect option will appear in the Network menu and

your wireless network profile will also be saved, thus

your TV will connect to the same network automati-

cally whenever you switch to wireless connection. To

disconnect from a wireless network and delete the

saved wireless network profile, highlight Disconnect

and press OK.

If your router has WPS, you can directly connect to the

modem/router without entering a password or adding

the network first. Highlight Press WPS on your wifi

router option and press OK. Go to your modem/router

device and press the WPS button on it to make the

connection. You will see a connection confirmation on

your TV once the devices have paired. Select OK to

proceed. No further configuration is required.

Highlight Internet Speed Test and press the OK button

to check your internet connection speed. Highlight

Advanced Settings and press the OK button to

open the advanced setting menu. Use directional and

numeric buttons to set. Highlight Save and press the

OK button to save settings when complete.

Other Information

The status of the connection will be displayed as

Connected or Not Connected and the current IP

address, if a connection is established.

Connecting to your mobile device via WLAN

• If your mobile device has WLAN feature, you can

connect it to your TV via a router, in order to access

the content in your device. For this, your mobile

device must have an appropriate sharing software.

Connect your TV to your router following the steps

mentioned in the sections above.

Afterwards, connect your mobile device to the router

and then activate the sharing software on your mobile

device. Then, select files that you want to share with

your TV.

If the connection is established correctly, you will

be able to access the shared files installed on your

mobile device via the Audio Video Sharing feature

of your TV.

Highlight the Audio Video Sharing option in the

Sources menu and press OK, available media server

devices in the network will be displayed. Select your

mobile device and press the OK button to continue.

• If available, you can download a virtual remote

controller application from the server of your mobile

device application provider.

Note: This feature may not be supported on all mobile

devices.

Networked Standby Mode

Networked Standby Mode is standard that allows

a device to be turned on or woken up by a network

message. The message is sent to the device by a

program executed on a remote device connected to

the same local area network, such as a smartphone.

Your TV is WoL and WoWLAN compatible. This feature

might be disabled during the First Time Installation

process. To enable this feature set the Networked

Standby Mode option in the Network menu as On.

It is necessary that both the device, from which the

network message will be sent to the TV, and the

TV are connected to the same network. Networked

Standby Mode feature is only supported for Android

OS devices and can only be used via YouTube and

Netflix applications.

In order to use this feature the TV and the remote

device should be connected at least once while the

TV is on. If the TV is powered off, the connection

should be re-established, the next time it is switched

on. Otherwise this feature will be unavailable. This

English - 34 -

(**) Limited Models Only