Whirlpool UXG7360VDS0 사용 및 관리 매뉴얼 - 페이지 6

{카테고리_이름} Whirlpool UXG7360VDS0에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool UXG7360VDS0 28 페이지. 30" (76.2cm), 36" (91.4cm) and 48" (121.9cm) wall-mount canopy grill vent hood installation instructions

Whirlpool UXG7360VDS0 사용 및 관리 매뉴얼
• Ifthehouse h asaluminum w iring follow theprocedure below:
1. Connect asection o fsolid copper wire tothepigtail
leads.
2. Connect thealuminum w iring totheadded section o f
copper wire using special connectors and/or tools
designed andULlisted forjoining copper toaluminum.
Follow theelectrical connector manufacturer's
recommended
procedure. Aluminum/copper
connection must c onform with
local c odes and industry a ccepted wiring practices.
Wire sizes andconnections must c onform withtherating of
theappliance asspecified onthemodel/serial
rating plate.
The model/serial
plate islocated b ehind t hefilter ontherear
wall o fthehood.
Wire sizes must c onform totherequirements
oftheNational
Electrical Code, ANSI/NFPA
70(latest edition), orCSA
Standards C22.1-94, Canadian Electrical Code, Part 1 and
C22.2 No. 0 -M91 (latest edition) and alllocal c odes a nd
ordinances.
INSTALLATION INSTRUCTIONS
'
}ccs on
It is recommended
that the vent system be installed before
2. Pivot the back edge of the filter towards the back of the grill
hood is installed,
vent hood.
Before making cutouts, make sure there is proper clearance
within the ceiling or wall for exhaust vent.
Check your ceiling height and the hood height maximum
before you select your hood.
1. Disconnect
power.
2. Determine which venting method to use: roof or wall.
3. Select a flat surface for assembling the grill vent hood. Place
covering over that surface.
Excessive Weight Hazard
Use two or more people to move and install grill
vent hood.
Failure to do so can result in back or other injury.
4. Using 2 or more people, lift grill vent hood onto covered
surface. Tip the hood on its back and remove filters and set
aside.
To Remove
Filters:
1. Using the filter handles, pull filter towards the front of the grill
vent hood.
B
<_
A
C
A. Filter handles
B. Front edge of filter
C. Back edge of filter
3. Drop the front edge of the filter down and remove.
Wood Mounting Strip Installation
1.
Determine and mark the centerline on the wall where the grill
vent hood will be installed.
Based on the ceiling or soffit height, determine the distance
"X" (30" [76.2 cm] min, 36" [91.4 cm] max) needed between
the cooking surface and the bottom of the grill vent hood. To
this distance, add 15%" (43.8 cm) and draw a horizontal line
(A) about 24" (61.0 cm) long centered on the vertical
centerline (B) at this distance for the wood mounting strip.
/
t
E\
A. Horizontal fine - mounting strip location
B. 15 _" (43.8 cm) - bottom of vent hood to
mounting strip location
C. Distance "X" (30" [76.2 cm] min, suggested
36" [91.4 cm] max) - cooking surface to
bottom of vent hood
D. Vertical centerline
E. Cooking surface
2. Locate and mark the wall studs along the horizontal line.
3. Center the 1" x 4" (2.5 x 10.2 cm) wood mounting strip above
the horizontal line.
6