Whirlpool UXL6036YSS0 설치 지침 및 사용 및 관리 매뉴얼 - 페이지 4
{카테고리_이름} Whirlpool UXL6036YSS0에 대한 설치 지침 및 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool UXL6036YSS0 36 페이지. 36" (91.4 cm) and 48" (121.9 cm) hood liner
페이지 인쇄
INSTALLATION REQUIREMENTS
Gather the required tools and parts before starting installation.
Read and follow the instructions
provided with any tools listed
here.
Tools needed
•
Level
•
Drill
•
1W' (3 cm) drill bit
•
V8" (3 mm) drill bit
•
Pencil
•
Wire stripper or utility knife
•
Tape measure or ruler
•
Pliers
•
Caulking gun and weatherproof
caulking compound
•
Vent clamps
•
Jigsaw or keyhole saw
•
Flat-blade screwdriver
•
Metal snips
•
Phillips screwdriver
Parts needed
•
Home power supply cable
•
1 - 1/2"(1.3 cm) UL listed or CSA approved strain relief
•
3 UL listed wire connectors
•
1 wall or roof cap
•
Metal vent system
•
Blower motor system - internal or external (see "Blower
Motor System" in the "Accessories"
section).
Parts supplied
Remove parts from packages. Check that all parts are included.
•
3 metal grease filters
•
Hood liner with halogen lamps installed.
•
1 - 10" (25.4 cm) square to 10" (25.4 cm) round duct
transition with damper.
•
4- 5 x 45 mm mounting screws
•
4- 4.2 x 8 mm screws
•
T-20 TORX®t adapter
IMPORTANT." Observe all governing codes and ordinances.
Have a qualified technician install the hood liner. It is the
installer's responsibility
to comply with installation clearances
specified on the model/serial rating plate. The model/serial
rating
plate is located behind the left filter on the rear wall of the hood
liner.
The hood liner location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given
dimensions
provide minimum clearance.
The hood liner must be surrounded
by a custom built enclosure
with hood support capable of supporting
75 Ib (34 kg).
Grounded electrical outlet is required. See "Electrical
Requirements"
section.
All openings in ceiling and wall where canopy hood will be
installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured
Home Construction
Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction
and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured
Home
Installation 1982 (Manufactured
Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local
codes.
Cabinet Dimensions
;_-- 36" (91.4 cm) for 36" models
__
48" (121.9 cm) for 48" models
L
....
(
....
....
,
.- /
22" (55.9 cm)
/_
....
-_
Hood liner depth
Hood support
must be
|
....
capable
of supporting
|
75 Ib (34 kg)
J
"X" bottom
_ _
of canopy
to
.....
cooking
surface
IM PO RTANT:
Minimum distance "X": 24" (61 cm) from electric cooking
surfaces.
Minimum distance "X": 30" (76.2 cm) from gas cooking
surfaces.
Suggested maximum distance "X": 36" (91.4 cm).
I"®TORX is a registered trademark
of Saturn Fasteners, Inc.