Whirlpool UXT2030AD 설치 지침 및 사용 및 관리 매뉴얼 - 페이지 3

{카테고리_이름} Whirlpool UXT2030AD에 대한 설치 지침 및 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool UXT2030AD 28 페이지. 30" (76.2 cm) range hood
Whirlpool UXT2030AD에 대해서도 마찬가지입니다: 설치 지침 및 사용 및 관리 매뉴얼 (28 페이지), 설치 지침 및 사용 및 관리 매뉴얼 (32 페이지)

페이지 인쇄

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

Metal snips

#2 Phillips

screwdriver

Pencil

Caulking gun and weatherproof

caulking compound

Jigsaw or keyhole saw

Parts supplied

Remove parts from package. Check that all parts are included.

#8-18 x 1"

(4.2 x 25 mm)

flat-head screws

Drywall

anchors

Short Phillips

head screws

3¹⁄₄" x 10" (8.3 x 25.4 cm)

rectangular damper

Parts needed

UL Listed/CSA

Approved ¹⁄₂" (13 mm)

Approved

strain relief

wire connectors

INSTALLATION REQUIREMENTS

Wire stripper

Flat-blade

screwdriver

Drill with ¹⁄₈"

(3 mm), ¹⁄₂"

(13 mm)

and 1¹⁄₄"

(3 cm) bits

#8-18 x ⁵⁄₈"

(4.2 x 16 mm)

truss-head screws

Mounting

brackets

120V, 75W

maximum,

type E26

incandescent lamp

For 7" (17.8 cm) round vented installations

7" (17.8 cm)

round

metal vent

system with

wall or roof cap

Vent clamps as

required

For 3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular vented installations

3¹⁄₄" x 10"

(8.3 x 25.4 cm) rectangular

metal vent system with

wall or roof cap

Optional accessories

Power

Charcoal

cord kit

filter kit

Part Number

W10355452*

W10355450*

*For information on ordering, see the "Assistance or Service"

section.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

It is the installer's responsibility to comply with installation

clearances specified on the model/serial rating plate. The

model/serial rating plate is located inside the range hood on

the left wall.

Range hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance. Consult the

cooktop/range manufacturer installation instructions before

making any cutouts.

This range hood is recommended for use with cooktops with

a maximum total rating of 40,000 Btus or less.

Grounded electrical outlet is required. See "Electrical

Requirements" section.

All openings in ceiling and wall where range hood will be

installed must be sealed.

These range hoods are factory set for vented installations.

Models that are capable of being installed as non-vented

(recirculating) require charcoal filters. See the "Assistance or

Service" section for information on ordering charcoal filters.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local

codes.

7" (17.8 cm)

round damper

Part Number

W10355451*

7" (17.8 cm)

round vent

mounting plate

Part Number

W10388168*

Duct tape

Stainless steel

cleaner and

polish

Part Number

31462A*