Whirlpool UXT2030AD 설치 지침 및 사용 및 관리 매뉴얼 - 페이지 4
{카테고리_이름} Whirlpool UXT2030AD에 대한 설치 지침 및 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Whirlpool UXT2030AD 28 페이지. 30" (76.2 cm) range hood
Whirlpool UXT2030AD에 대해서도 마찬가지입니다: 설치 지침 및 사용 및 관리 매뉴얼 (28 페이지), 설치 지침 및 사용 및 관리 매뉴얼 (32 페이지)
페이지 인쇄
Tools and Parts
Gather the required tools and parts before starting
installation. Read and follow the instructions provided
with any tools listed here.
Tools needed
Metal snips
#2 Phillips
screwdriver
Pencil
Caulking gun and weatherproof
caulking compound
Jigsaw or keyhole saw
Parts supplied
Remove parts from package. Check that all parts are included.
#8-18 x 1"
(4.2 x 25 mm)
flat-head screws
Drywall
anchors
7" (17.8 cm) round vent
mounting plate
Part Number W10388168*
Parts needed
UL Listed/CSA
Approved
wire connectors
For 7" (17.8 cm) round vented installations
Vent clamps as
required
7" (17.8 cm) round
metal vent system with
wall or roof cap
4
INSTALLATION REQUIREMENTS
Wire stripper
Flat-blade
screwdriver
Drill with ¹⁄₈"
(3 mm), ¹⁄₂"
(13 mm)
and 1¹⁄₄"
(3 cm) bits
#8-18 x ⁵⁄₈"
(4.2 x 16 mm)
truss-head screws
Mounting
brackets
120V, 75W
maximum,
type E26
lamp
7" (17.8 cm)
round damper
Part Number
W10355451*
Optional accessories
Power
cord kit
Part Number
W10355452*
* For information on ordering, see the "Assistance or Service"
section.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
It is the installer's responsibility to comply with installation
■
clearances specified on the model/serial rating plate.
The model/serial/rating plate is located inside the range
hood on the left wall.
Range hood location should be away from strong draft
■
areas, such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be
■
used. Given dimensions provide minimum clearance.
Consult the cooktop/range manufacturer installation
instructions before making any cutouts.
This range hood is recommended for use with cooktops
■
with a maximum total rating of 40,000 Btus or less.
Grounded electrical outlet is required. See "Electrical
■
Requirements" section.
All openings in ceiling and wall where range hood will
■
be installed must be sealed.
These range hoods are factory set for vented installations.
■
Models that are capable of being installed as non-vented
(recirculating) require charcoal filters. See the "Assistance or
Service" section for information on ordering charcoal filters.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title
24 CFR, Part 328 (formerly the Federal Standard for Mobile
Home Construction and Safety, title 24, HUD, Part 280)
or when such standard is not applicable, the standard for
Manufactured Home Installation 1982 (Manufactured Home
Sites, Communities and Setups) ANSI A225.1/NFPA 501A,
or latest edition, or with local codes.
Product Dimensions
2"
(5.1 cm)
4¹⁵⁄₁₆"
1"
(12.5 cm)
(2.5 cm)
29¹⁵⁄₁₆" (76.0 cm)
Stainless steel cleaner
and polish
Part Number 31462A*
6⁹⁄₁₆" (16.7 cm)
9"
(22.9 cm)
1¹⁄₂"
18⁵⁄₈"
(3.8 cm)
(47.3 cm)
1"
(2.5 cm)