Xerox 6180N - Phaser Color Laser Printer 시작하기 매뉴얼 - 페이지 24

{카테고리_이름} Xerox 6180N - Phaser Color Laser Printer에 대한 시작하기 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox 6180N - Phaser Color Laser Printer 34 페이지. Color laser printer
Xerox 6180N - Phaser Color Laser Printer에 대해서도 마찬가지입니다: 설치 매뉴얼 (34 페이지), 사양 시트 (2 페이지), 사용자 설명서 (32 페이지), 사용자 설명서 (28 페이지), 설치 매뉴얼 (2 페이지), 보안 매뉴얼 (38 페이지), 릴리스 노트 (2 페이지), 설치 매뉴얼 (2 페이지), 시작하기 매뉴얼 (37 페이지), 매뉴얼 (34 페이지), 매뉴얼 (34 페이지), 사용자 설명서 (32 페이지), 설치 및 운영 매뉴얼 (8 페이지), 평가자 매뉴얼 (16 페이지), 사양 (4 페이지)

페이지 인쇄
Xerox 6180N - Phaser Color Laser Printer 시작하기 매뉴얼
20
Caveat
External finishing cannot be selected at the
client using the IPP or HTTP gateways.
Submit the job to the printer without any
finishing, and select the external finisher at
the DocuSP.
Jobs with a Layout custom template and 1 Up
may complete with errors.
In DocuSP 3.8, Offset was a system-level
setting and ON by default. In DocuSP 4.x,
Offset is a queue setting and is OFF by
default. Check the queue setting for Offset to
ensure it is set as needed.
Using a streaming queue is not
recommended. Jobs hang with a status of
"Waiting for RIP."
Custom ICC profile files may not be restored
after a Configuration Restore.
An FRF saved job displays incorrectly in the
viewer, but prints correctly.
Jobs print in serial mode when the
administration pages and Page Parallel RIP
are enabled. In order for jobs to print in
parallel mode, disable the administration
(banner and error) pages.
The AppleTalk Gateway is not being restored
in the UI after a Configuration Restore. You
will need to reconfigure this gateway.
After clearing a faulted job, the fault message
is not erased.
A streaming job caused a fatal system error. If
possible, resubmit the job to a spooling
queue.
When deselecting Booklet as the output
layout model, Sides Imaged remains 2-sided.
Be sure to check the sides imaged setting
after deselecting Booklet as the layout model.
System Configuration Restore does not
properly restore certain network configuration
files, causing DocuSP to not boot.
TBD: Does going into DocuSP Network
Configuration and setting the DNS
configuration fix the problem? TBD
A job may print with the incorrect font on a
page or the text may overwrite itself.
Set the True Type Spot Size to 1.4. Controls
for this setting can be found in Printer
Manager: Image Quality: PostScript context.
Applicable printer product
DocuPrint 1xx EPS
DocuTech 61xx
DocuColor 8000
DocuColor
2045/2060/6060/5252/8000
DocuColor
2045/2060/6060/5252/8000
All color printers
All color printers
All color printers
DocuPrint CF
DocuPrint 1xx EPS
DocuTech 61xx
DocuPrint 1xx EPS
DocuTech 61xx
DocuPrint 1xx EPS
DocuTech 61xx
DocuPrint 1xx EPS
DocuTech 61xx
DocuPrint 1xx EPS
DocuTech 61xx
DocuPrint 1xx EPS
DocuTech 61xx