Yamaha HTR-5130 소유자 매뉴얼 - 페이지 15

{카테고리_이름} Yamaha HTR-5130에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Yamaha HTR-5130 42 페이지. Natural sound av receiver

페이지 인쇄

›

PHONES jack

To listen with headphones, connect the headphones to the

PHONES jack. The sound output from the PHONES jack is the

same as that from the main speakers.

When listening with headphones privately, set both the

SPEAKERS A and B switches to the OFF position and switch

off the digital sound field processor (so that no DSP program

indicator is lit in the display) by pressing the EFFECT button.

SPEAKERS switches

Set the switch A or B (or both A and B) for the main speaker

system (connected to this unit) you will use to the ON position.

Set the switch for the main speaker system you will not use to

the OFF position. (Refer to page 25.)

ﬁ

A/B/C/D/E button

Press this button to select a desired group (A–E) of preset

stations. (Refer to page 27.)

Preset station number selector buttons

Press to select a preset station number (1 to 8). (Refer to page

27.)

ﬂ

Tone controls

These controls are effective only for the sound from the main

speakers. (Refer to page 25.)

BASS

Used to increase or decrease the low frequency response.

The 0 position produces flat response.

TREBLE

Used to increase or decrease the high frequency response.

The 0 position produces flat response.

BALANCE control

This control is effective only for the sound from the main

speakers.

Adjusts the balance of the output volume to the left and right

speakers to compensate for sound imbalance caused by

speaker location or listening room conditions. (Refer to page

25.)

‡

RDS MODE/FREQ button

When an RDS station is received, pressing this button

repeatedly changes the display to the PS mode, PTY mode,

RT mode, CT mode (RDS services subject to availability), and

station frequency in turn. (Refer to page 32.)

PTY SEEK MODE button

When this button is pressed, the unit turns into the PTY SEEK

mode. (Refer to page 33.)

PTY SEEK START button

Press this button to begin searching for a station after the

desired program type is selected in the PTY SEEK mode.

(Refer to page 33.)

PHONES

HTR-5130RDS only

(

EON button

HTR-5130RDS only

Press this button to select a specified program type (NEWS,

INFO, AFFAIRS, SPORT) when you want to locate a radio

program of that type automatically. (Refer to page 34.)

TUNING DOWN/UP button

Use for tuning radio stations. Press the UP side to tune in to

higher frequencies, and press the DOWN side to tune in to

lower frequencies.

HTR-5130RDS only

When this unit is in the PTY SEEK mode,

press either side of this button to change the currently selected

program type.

)

DSP program selector buttons

Select a DSP program. When a button is pressed, the name of

selected program lights up on the display. (Refer to page 35.)

‚

EFFECT button

Switches the digital sound field processor on and off (including

the Dolby Pro Logic Surround decoder). (Refer to page 36.)

CENTER MODE button

Selects a center channel output mode (NORMAL, WIDE or

PHANTOM). (Refer to page 20.)

—

DELAY/CENTER/REAR/SWFR and TIME/LEVEL +/–

buttons

Adjust the delay time (DELAY), the center channel output level

(CENTER), the rear channel output level (REAR) and the

output level to the SUBWOOFER OUTPUT terminal (SWFR).

Select the item which you want to adjust by pressing the

DELAY/CENTER/REAR/SWFR button and adjust its time or

level by pressing the TIME/LEVEL +/– button. (Refer to pages

25, 37, and 38.)