ARO Ingersoll-Rand PX10P-APS Series 운영자 매뉴얼 - 페이지 6
{카테고리_이름} ARO Ingersoll-Rand PX10P-APS Series에 대한 운영자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ARO Ingersoll-Rand PX10P-APS Series 8 페이지. 1” diaphragm pump
페이지 인쇄
n
Indicates parts included in 637397 Air Section Service Kit shown below and items (70), (144), (175) and (180) shown on page 4.
Item
Description
(size)
101 Center Body
103 Bushing
105 Screw
(M6 x 1 6g x 130 mm)
107 End Plate
111 Spool
n
118 Actuator Pin
121 Sleeve
132 Gasket
n
133 Washer
(M6)
134 Screw
(M6 x 1 6g x 20 mm)
135 Valve Block
(PD10P XXS XXX)
(PE10P XXS XXX)
136 End Cap
137 Gasket
n
138 U" Cup
(3/16" x 1 5/8" o.d.)
n
139 U" Cup
(3/16" x 1 1/8" o.d.)
n
140 Valve Insert
141 Valve Plate
166 Gasket
n
167 Pilot Piston
(includes 168 and 169)
n
K Fluid Section Service Kit parts, see page 4.
AIR MOTOR SECTION SERVICE
Service is divided into two parts - 1. Pilot Valve, 2. Major Valve.
GENERAL REASSEMBLY NOTES:
S
Air Motor Section Service is continued from Fluid Section repair.
S
Inspect and replace old parts with new parts as necessary. Look for
deep scratches on surfaces, and nicks or cuts in O" rings.
S
Take precautions to prevent cutting O" rings upon installation.
S
Lubricate O" rings with Lubriplate FML 2 grease.
S
Do not over tighten fasteners, refer to torque specification block on
view.
S
Re torque fasteners following restart.
S
SERVICE TOOLS - To aid in the installation of (168) O" rings onto
the (167) pilot piston, use tool # 204130 T, available from ARO.
PILOT VALVE DISASSEMBLY
1. A light tapping on (118) should expose the opposite (121) sleeve,
(167) pilot piston and other parts.
2. Remove (170) sleeve, inspect inner bore of sleeve for damage.
PILOT VALVE REASSEMBLY
1. Clean and lubricate parts not being replaced from service kit.
2. Install new (171 and 172) O" rings, replace (170) sleeve.
3. Install new (168) O" rings and (169) seal Note the lip direction. Lu
bricate and replace (167).
4. Reassemble remaining parts, replace (173 and 174) O" rings.
Page 6 of 8
PARTS LIST / PX10P-X AIR SECTION
AIR MOTOR PARTS
Qty Part No.
[Mtl]
(1)
95970
[P]
(1)
96000
[D]
(4)
95886
[SS]
(2)
95840
[SS]
(1)
96293
[D]
(2)
95999
[SS]
(2)
95123
[D]
(1)
95841
[B]
(6)
95931
[SS]
(6)
95887
[SS]
(1)
96174 1
[P]
(1)
96174 2
[P]
(1)
95833
[P]
(1)
95844
[B]
(1)
Y186 53
[B]
(1)
Y186 49
[B]
(1)
95838
[AO]
(1)
95885
[AO]
(1)
96004
[B]
(1)
67164
[D]
1. Remove (135) valve block and (233) adapter plate, exposing (132
2. Insert a small flat blade screwdriver into the notch in the side of (135)
3. Remove (136) end cap and (137) gasket, releasing (111) spool.
1. Install new (138 and 139) U" cups on (111) spool - LIPS MUST
2. Insert (111) spool into (135) valve block.
3. Install (137) gasket on (136) end cap and assemble end cap to (135)
4. Install (140) valve insert and (141) valve plate into (135) valve block.
5. Assemble (200) gasket and (233) adapter plate to (135) valve block.
6. Assemble (132 and 166) gaskets and (176) checks and to (101)
7. Assemble (135) valve block and components to (101) body, secur
Item
Description
(size)
168 O" Ring
(3/32" x 5/8" o.d.)
169 U" Cup
(1/8" x 7/8" o.d.)
170 Piston Sleeve
171 O" Ring
(3/32" x 1 1/8" o.d.)
n
172 O" Ring
(1/16" x 1 1/8" o.d.)
n
173 O" Ring
(3/32" x 1 3/8" o.d.)
n
174 O" Ring
K
(1/8" x 1/2" o.d.)
n
176 Diaphragm
(check valve)
n
181 Roll Pin
(5/32" o.d. x 1/2" long)
200 Gasket
n
201 Muffler
233 Adapter Plate
236 Nut
(M6 x 1 6h)
L
Lubriplate FML 2 Grease
n
Lubriplate Grease Packets (10)
MATERIAL CODE
[AO] = Alumina Oxide
[D] =
Acetal
[B] =
Nitrile
[P] =
Polypropylene
[Br] = Brass
[SP] = Santoprene
MAJOR VALVE DISASSEMBLY
and 166) gaskets and (176) checks.
valve block and push in on tab to remove (233) adapter plate, releas
ing (140) valve insert, (141) valve plate and (200) gasket.
MAJOR VALVE REASSEMBLY
FACE EACH OTHER.
valve block, securing with (107) end plates and (105) screws.
NOTE: Tighten (105) screws to 35 40 in. lbs (4.0 4.5 Nm).
NOTE: Assemble (140) valve insert with dished" side toward (141)
valve plate. Assemble (141) valve plate with part number identifica
tion toward (140) valve insert.
NOTE: Assemble (233) adapter plate with notched side down.
body.
ing with (134) screws. NOTE: Tighten (134) screws to 35 40 in. lbs
(4.0 4.5 Nm).
Qty Part No.
[Mtl]
(2)
94433
[U]
(1)
Y240 9
[B]
(1)
94081
[Br]
(1)
Y325 119
[B]
(1)
Y325 22
[B]
(2)
Y325 123
[B]
(2)
Y325 202
[B]
(2)
95845
[SP]
(4)
Y178 52 S
[SS]
(1)
95842
[B]
(1)
93139
[P]
(1)
95832
[P]
(4)
95924
[SS]
(1)
94276
637308
[SS] = Stainless Steel
[U] =
Polyurethane
PD10P X