3M SLR 650G 사용 설명서 - 페이지 2

{카테고리_이름} 3M SLR 650G에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. 3M SLR 650G 9 페이지. 3m overhead projector operating instructions model no. 1700

페이지 인쇄

INTENDED USE

Before operating the machine, please read the entire manual

thoroughly. The 3M™ Overhead Projector 1700 was

designed, built and tested for use indoors, using 3M brand

lamps and nominal local voltages.

IMPORTANT SAFEGUARDS

When using your overhead projection equipment, basic

safety precautions should always be followed, including

the following:

1. Read and understand all instructions before using.

Pay particular attention to areas where this symbol

is shown.

2. Close supervision is necessary when any appliance

is used by or near children. Do not leave appliance

unattended while in use.

Care must be taken as burns can occur from

touching hot parts.

4. Do not operate appliance with a damaged cord or if

the appliance has been dropped or damaged until it

has been examined by a qualified service

technician.

Position the cord so that it will not be tripped over,

pulled, or contact hot surfaces.

6. If an extension cord is necessary, a cord with a

current rating at least equal to that of the appliance

should be used. Cords rated for less amperage

than the appliance may overheat.

7. Always unplug appliance from electrical outlet

before cleaning and servicing and when not in use.

Never yank cord to pull plug from outlet. Grasp plug

and pull to disconnect.

THANK YOU

Thank you for choosing 3M overhead projection equipment.

This product has been produced in accordance with 3M's

highest quality and safety standards to ensure a smooth and

troublefree use in the years to come. Your purchase of this

product proves that you appreciate this.

Part Identification List

Open Projection Head

Projection Mirror

Singlet Lens (1705, 1708)Triplet Lens (1720, 1750)

Arm

Focus Knob

Post

Post Latch

Post Cradle

On/Off Power Switch

10. High/Low Brightness Switch (1708, 1720, 1750)

11. Color Tuning Knob (1708, 1720, 1750)

12. Lamp Changer (1708, 1720, 1750)

13. Top Cover Release Latch (with interlock)

14. Top Cover Stage Glass

15. Cord Storage

16. Power Cord

3M 1700 Operator's Guide

The use of other replacement lamps, outdoor operation or

different voltages has not been tested, and could damage the

projector or peripheral equipment and/or create a potentially

unsafe operating condition.

Let appliance cool completely before putting away

or when replacing lamp.

To reduce the risk of electric shock, do not

immerse this appliance in water or other liquids.

10. To reduce the risk of electric shock, do not

disassemble this appliance, but take it to a

qualified technician when service or repair work is

required. Incorrect reassembling can cause electric

shock when the appliance is used subsequently.

11. The use of an accessory attachment not

recommended by the manufacturer may cause a

risk of fire, electric shock, or injury to persons.

12. Do not overload accessory circuit (if equipped).

13. Connect this appliance to a grounded outlet.

14. Disconnect this unit from its source of supply

before replacing the projection lamp.

15. This unit is equipped with optical lenses and

should not be exposed to direct sunlight.

16. Keep ventilation openings free of any obstructions.

17. This unit is connected by a special power cord that,

if damaged, has to be replaced by the same type

of power cord. This part can be ordered from your

local 3M dealer and has to be installed by a

qualified service technician.

SAVE THESE INSTRUCTIONS

The information contained in this manual will help you

operate and maintain your Overhead Projector.

For optimum performance we kindly ask you to follow these

operating instructions carefully. We hope you will enjoy using

this high performance product in your meeting, training and

presentation sessions.

17. Machine Identification Plate