Asko D5434XL W 사용 설명서 - 페이지 8

{카테고리_이름} Asko D5434XL W에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Asko D5434XL W 20 페이지. Dishwasher

페이지 인쇄

Normal wash

Use to wash normally soiled dishes, such as plates, serving

dishes, cups, glasses, and so on.

Eco wash

Use when you want to save energy. For normally soiled dishes.

Quick wash

This program is used for glasses and porcelain that is lightly

soiled, such as coffee cups.

Rinse & Hold

Use to rinse dishes while you wait for the dishwasher to become

fully loaded.

Selecting Options

To select an option, press one of the option buttons. The field

next to the button lights when the option is activated. The available

options depend on the selected program. Once you have started

the program, the options you selected are saved for the next time

you use the same program.

High temperature

Activate this option for improved dishwashing results. The

machine then uses a higher temperature for the main wash.

If you want to use the lower temperature, press until the field next

to the button turns off.

You can vary the temperature as shown below:

Sanitation wash:

Normal wash:

Heavy wash:

Quick wash:

Eco wash:

Long dry

A higher temperature in the final rinse and a longer drying phase

improves the drying result if you activate the Long dry option.

This causes a slight increase in energy consumption.

If you want a program with Short dry, press so that the field next

to the button turns off.

Start the dishwasher

Press and hold Start until the display flashes three times with the

remaining time. This indicates that the program has started. Close

the door properly, otherwise the dishwasher will not start. The

display indicates

130 °F (55 °C) / 160 °F (70 °C)

130 °F (55 °C) / 150 °F (65 °C)

140 °F (60 °C) / 150 °F (65 °C)

85 °F (30 °C) / 140 °F (60 °C)

120 °F (50 °C) / 140 °F (60 °C)

if the door is open.

Customer Care Center 1-800-898-1879

NOTE!

If the machine does not start within 2 minutes of the last button

press, the display returns to showing the last program run.

Time remaining

Once you have selected a program and options, the display

indicates how long the program took the last time it was used.

Once you have started the dishwasher, the display indicates how

much program time remains. The remaining time is updated after

the water for the final rinse has been heated.

This may differ somewhat from time to time depending on the

temperature of the water supply, the amount of dishes, the

ambient temperature, and other factors.

The time counts down while the program is running and the

remainder of the program is displayed. The remaining time is

displayed, e.g., 1:15, meaning that 1 minute 15 seconds of the

program remains.

NOTE!

During the first run of each program, the remaining time

displayed can be slightly misleading, as the dishwasher is

estimating the time. When you run the program a second time,

the dishwasher will calculate the remaining time based on the

previous duration of the program.

Stopping or changing a program

If you want to change programs after starting the dishwasher,

open the door then press and hold Stop for five seconds. Add

more detergent if the lid of the detergent dispenser has opened.

Then choose a new program, press Start, and close the door.

Do you want to add more dishes?

Open the door. The dishwasher stops automatically. Add the

dishes, close the door, and the dishwasher resumes the program.

If the dishwasher is turned off using

the main power switch or due to a

power failure

If the program was not finished, the interrupted program resumes

when power is restored.

NOTE!

During drying, the program is interrupted if the power is cut or

the door is open for more than 2 minutes.

Once the program has finished

Once the program has finished, "End" appears on the display.

A buzzer also sounds at the end of the program. See the section

Settings, which describes how to change this function.

Once the dishwasher has finished, it uses only standby power.

Turn off the dishwasher using the main power switch if you want

to completely cut the power. Turn off the water supply valve after

each use.