Asko T761 빠른 시작 매뉴얼 - 페이지 2

{카테고리_이름} Asko T761에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Asko T761 2 페이지. User manual quick start guide en
Asko T761에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (2 페이지), 기획 및 디자인 매뉴얼 (19 페이지), 빠른 시작 매뉴얼 (2 페이지)

페이지 인쇄

QUICK START PROCEDURES

Press the Power button to turn on the machine.

Load the dryer.

Check the lint filter. Clean it, if needed.

Check that the door is clear of laundry then close it firmly. (The door wont shut if its slammed.)

Press the button for the desired program (P1P4).

Press Start. The machine will start.

UNDERSTANDING THE LCD WINDOW

The LCD window is easy to read and understand. The illustration below explains what each item on the LCD window is.

Program

When you press the Power button,

the display toggles between the

program numbers and the wash

program names, (e.g., Extra Dry,

Dry, etc.)

Preset Programs

Displays the program that

is selected/running.

The LCD window also displays the menus and options available when you customize the preset programs. Refer to your Use and Care

Guide for more details.

CLEANING THE LINT FILTER

Although the lint in your ASKO dryer will be minimal, the lint filter should be cleaned after each load

to ensure maximum air flow and prevent possible overheating. To clean the filter, follow the steps

below:

1. Grasp the handle and pull it toward you.

2. Remove the filter from the holder by pulling it up.

3. Open the filter and gently brush away any lint.

4. Fold the filter together and return it to the holder on the door.

5. Push the holder in until it snaps into place.

We recommend that you clean the lint filter after every load.

NOTE:

EMPTYING THE CONDENSATION WATER CONTAINER

If Model T781 is not installed to pump out the condensed water into a drain or a sink, you should empty the

water container every three to five dryer loads, depending on the spin speed you use when you wash the

clothes. For example, clothes spun at 800 rpm will have more moisture when you take them out of the

washer than clothes spun at 1400 rpm. Therefore, the dryer will have to remove more water.

To empty the container, simply pull it out and pour out the water. This water is clean and can be used to water

plants.

If the container becomes too full, the machine will shut down. To restart the program, empty the container and

press Start. It may be a few minutes before the machine starts because it drains the excess water from the sump before it restarts.

OVERHEATING PROTECTION

The dryer has a protection device that shuts the machine off if the temperature becomes too high. Overheating could occur if the lint filter is

clogged or if the fan or condenser unit (Model T781) needs to be cleaned. If the dryer shuts off during a program on Model T781, first, make

sure the condensation water container is empty. If that isnt the problem, check the lint filter. Lastly, it could be the fan or condenser unit needs

to be cleaned. See your Use and Care Guide for instructions on how to clean these items.

Start

Indicates that you pressed Start

and the program is running.

NOTE:

Do not remove the water container while the machine is running.

Program Time

When you start a program, the total time the

program runs is displayed. As the program

progresses, the time remaining displays. The

program time toggles between minutes (e.g.,

23) and hours (e.g., 1h).

Stop

Indicates that the program has ended

or that you pressed Stop.

T761/T781

(T781 only)

Art. No. 80 646 44 Rev. 02