AMD DIrect SSRFR-24DK1 User Manual - Page 6

Browse online or download pdf User Manual for Kegerators AMD DIrect SSRFR-24DK1. AMD DIrect SSRFR-24DK1 9 pages.

Print Page

OPERATING YOUR APPLIANCE

CONTROL PANEL

ON/OFF POWER

To turn the appliance ON or OFF, press and hold the

POWER key

for 5 seconds.

AND DOWN

Press

first, then press

button

SET

to increase (warm) or decrease (cool) the set

temperature by 1°C/ 1°F.

Press

again, the temperature is selected and

SET

shows the actual temperature. If no other further

operation in 6 seconds, display will show actual

temperature in the cooler

°F/°C SELECTOR

Selects the temperature display setting in Fahrenheit

or Celsius degrees. To change the temperature from

Fahrenheit to Celsius or from Celsius to Fahrenheit,

press

and

at the same time, then hold for 6

SET

seconds.

SETTING THE TEMPERATURE CONTROL

The temperature you are setting will increase by

one degree each time you press the

key and

will decrease by one degree each time you press

the

key.

The range of temperature control is from 32°F to 50°F.

To view the set temperature at any time, press

the

key. The set temperature will flash in the

SET

display window for 6 seconds. After 6 seconds, the

temperature inside the until will reappear in the

display window.

(The temperature preset at the factory is 36°F)

KEGERATOR USER MANUAL

OPERATION INSTRUCTION

The Kegerator is able to maintain the proper

dispensing temperature for beer, provided it is

installed correctly in the proper environment. For

best results, mount the draft tower as close to the top

of the kegerator as possible and seal any openings

to prevent heat transfer. Avoid opening and closing

the door of the kegerator too often to ensure a

consistent temperature inside the unit. Factory preset

temperature is 36 degrees Fahrenheit.

The Kegerator should be placed in an area where

the ambient temperature range is between 50-

109.4 degrees Fahrenheit (10-43 degrees Celsius).

If the ambient temperature is above or below this

range, the performance of the unit may be affected.

For example, placing your unit in extreme cold or

hot conditions may cause interior temperatures

to fluctuate. Please be aware that the desired

temperatures may fluctuate depending on the

ambient temperature and the orientation of the keg.

INSTALLATION

STEP 1

Unpackage your kegerator and lay out the kegerator

parts on a flat surface, ensuring you have the following:

1. CO2 Regulator

5. Keg Tower w/Hose

8. 4 Long Bolts, 4 Nuts &

2. Keg Coupler

6. Red Hose w/ 2 Fasteners

2 Rubber Washers

3. Keg Tap & Handle

7. 4 Short Bolts &

9. Tap Tray

4. CO2 Tank

4 Metal Washers

10. Keys

STEP 2

Then, guide the translucent hose through the kegerator

opening, or if you have an island, as shown, guide it

through both openings. If mounting to a counter-top,

secure your tower using the four long bolts & nuts,

and 2 rubber washers. If mounting directly onto your

kegerator, use the 4 short bolts and metal washers.

STEP 3

Now, screw the tap handle onto the Keg Tap, and fasten

the Keg Tap to the tower by rotating counterclockwise.

STEP 4

Locate the translucent hose connected to the Keg

Tower, and attach it to the Keg Coupler. Then, connect

the Keg Coupler to your keg by pushing down and

twisting clockwise to lock it in.

*DO NOT PUSH DOWN THE BLACK LEVER ON KEG COUPLER*

STEP 5

Then, attach the regulator to the CO2 tank, using an

adjustable wrench to avoid leakage. Place a metal

fastener around the neck of the red hose, and attach

the hose to the nozzle of the regulator. Tighten the

fastener using a flathead screwdriver. Place another

metal fastener around the other end of the red hose,

and attach to the nozzle on the Keg Coupler. Tighten

the metal fastener. Twist counterclockwise to open the

CO2 tank. Unscrew the pressure valve until loose, and

then re-screw until the pressure gauge reads "12"

STEP 6

Place your CO2 tank onto the shelf, and then

lift the keg into the kegerator. Tap your keg by

pulling out the black lever of your Keg Coupler,

pushing down, and releasing. Make sure your keg

completely cools before use. Place the Tap Tray

below the tap.

POUR AND ENJOY!