Air Design CSV42N Installation, User & Maintenance Manual - Page 8

Browse online or download pdf Installation, User & Maintenance Manual for Air Conditioner Air Design CSV42N. Air Design CSV42N 19 pages. Water cassettes csvn series; hcvn series

Print Page

RECCOMENDATIONS FOR THE INSTALLER

Upon receiving the unit check for any damage, which should be reported

immediately. For the water cassette to operate correctly, it should be installed

according to the instructions given in this manual. Removal of a water cassette

after it has been installed is an operation that requires special training: if this is

necessary, please consult your dealer. After installation, explain the correct

operating procedure to the customer using the booklet as a reference. Leave

this manual with the customer since it is part of the kit supplied with the appliance.

Take care not to scratch the units when handling them.

UNIT INSTALLATION

- Read this instruction manual thoroughly before starting installation.

- This unit complies with the low-voltage (EEC/73/23) and electromagnetic

compatibly (EEC/89/336) directives.

- The installation should be carried out by a qualified installer.

- Follow all current national safety code requirements. In particular ensure that

a properly sized and connected ground wire is in place.

- Check that the voltage and frequency of the mains power supply are as

required for the unit to be installed; the available power source must be

adequate to operate all other appliances connected to the same line.

- Ensure that national safety code requirements have been followed the main

supply circuit.

- Where necessary, use field-supplied 25 mm I.D. PVC pipe of appropriate

length and with the correct thermal insulation for the condensate drain

extension.

- After installation thoroughly test system operation and explain all system

functions to the owner.

- Use this only for factory approved applications: the unit cannot be used in

laundry or stream pressing premises.

WARNING!

- Disconnect the mains power supply switch before servicing the system or handling

any internal parts of the unit.

- The manufacturer declines any liability for damage resulting from modifications or

errors in the electrical or water connections.

- Failure to observe the installation instructions, or use the unit under conditions

other than those indicated in table Operating limits of this manual, will immediately

invalidate the unit warranty.

- Failure to observe electric safety codes may cause a fire hazard in the event of

short circuits.

- Do not install or use damaged units.

- In case of malfunction turn the unit off, disconnect the mains power supply and

contact a qualified service engineer.

- Maintenance must only be carried out by qualified personnel.

- All of the manufacturing and packaging materials used for this appliance are

biodegradable and recyclable.

- Dispose of the packaging material in accordance with local requirements.

RECEIVING, STORE AND MOVING THE UNITS

At the moment of the delivery of the unit, make sure that it corresponds to the

one indicated on the transport document. Check the integrity of the packing

and the unit. Should there be any differences with the original order or any

damages, anomalies, or incomplete supply, please point it out on the delivery

note and inform the firm straight away. Never install or use damaged apparatuses.

The unit can be stored in room protected from bad weather with temperature

between -20°C and +55°C. Transport the packed unit as near as possible to

the installation place. To avoid any damage to the unit, the plastic part (frontal

panel and grille) are furnished separately. The handling and the installation could

be facilitated by use of an elevator(fig. 07).

ATTENTION!

Lift up the cassette by the four corners. Don't

lift or move the unit through the exchanger

pipelines or the exhaust pipe condense.

Fig. 07

s e r i e s

CSVN

HCVN

INSTALLATION, USE AND

MAINTENANCE GUIDE

INSTALLATION ACCESSORIES

n. 1 Cardboard mounting template;

n. 2 Batteries;

n. 1 Remote control;

n. 1 Auxiliary drain pan;

SELECTION OF CASSETTE INSTALLATION LOCATION

RECCOMENDATION!! The unit must be installed in a solid and vibration-free

ceiling. There should be no obstruction of the air flow into and out of the unit

and the air should be evenly distributed throughout the whole room. Do not install

the unit near sources of heat, steam or inflammable gases. Install the unit near

an electric socket or connect it directly to the power supply. Do not install the

unit in a place, which is exposed to direct sunlight. The selected place should

allow easy drainage of the condensed water. Periodically check appliance

operation and leave sufficient space for maintenance around the appliance, as

shown in the figure 07. Install the unit so that the filter is easily accessible.

INSTALLATION

FIXING THE CASSETTE

Select a place of installation where there can be a clearance of a least 100 cm

(see fig. 08) around the appliance. Make sure that the installation does not

interfere with existing electric wiring or plumbing. Establish the position and size

of the hole in the ceiling using the external diameter of the cardboard mounting

template (fig. 09).

Select the final position of the unit in the ceiling using the references printed on

the cardboard mounting template (fig. 10).

Fig. 08

Fig. 09

To fix the unit to the ceiling, use the threaded bar and suitable screw anchors

as shown in fig. 09 (material not included in the supply).

Use a spirit level (fig. 11) to make sure that the unit is level and check that it

is securely fixed to the ceiling. In high humidity environments, metal supports

must be insulated using adhesive insulating material.

>100

Fig. 10