Advanced Native Technologies ING 30 User Manual - Page 6

Browse online or download pdf User Manual for Microphone Advanced Native Technologies ING 30. Advanced Native Technologies ING 30 15 pages. Ing series uhf in ear monitor systems sistemi in ear monitor uhf

Print Page

press again ESC (ING 30R) or SET (ING 20R) to exit the menu.

Simultaneously using more systems, it's better to have them on the same group

but on different channels.

If the transmitter is in Mono mode, using the up/down buttons you set the position

of the signal in the Stereo field.

4 TONE SELECTION (ING 30T only)

Press the SET button for 2 seconds to access the settings menu, then press again

SET until when "TONE" starts flashing in the display. Use the up and down buttons

to activate (ON) or deactivate (OFF) TONE feature.

TONE ON boosts high frequencies.

5 LIMITER SELECTION (ING 30T only)

Press the SET button for 2 seconds to access the settings menu, then press again

SET until when "LIMITER" starts flashing in the display. Use the up and down buttons

to activate (ON) or deactivate (OFF) LIMITER feature. LIMITER ON reduces sudden

peaks, thus protecting your hearing.

6 LOCK (ING 30T only)

Press the SET button for 2 seconds to access the settings menu, then press again

SET until when the lock icon starts flashing. Use the up and down buttons to activate

(ON) or deactivate (OFF) the lock.

ATTENTION: when LOCK icon is displayed, you can see the unit settings, which

are not editable.

7 MIX (ING 30T only)

Press the SET button for 2 seconds to access the settings menu, then press again

SET until when "MIX" starts flashing in the display. Use the up and down buttons to

activate (ON) or deactivate (OFF) MIX feature.

MIX ON allows to listen both transmitter input signals - AF1 and AF2 - using the

supplied earphones.

To balance the signal between AF1 and AF2 inputs, press the up and down buttons.

You can choose among 31 available positions:

In MIX -0- position, AF1 and AF2 input signals are balanced.

Press the (button arrow up) to increase AF1 signal versus AF2 signal:

1-, 2-, 3-, 4-, 5-, 6-, 7-,8-, 9-, A-, b-, C-, d-, E-, and F- (max)

Press the (button arrow down) to increase AF2 signal versus AF1 signal:

-1, -2, -3, -4, -5, -6, -7, -8, -9, -A, -b, -C, -d, -E, and -F (max)

8 BATTERIES LEVEL INDICATOR

This icon displays in 4 steps the battery charge level. When inside the icon there's no

bars present and LOW BATT LED flashes, please immediately replace the batteries.

ING Series

User manual |

Series

4 | TROuBLESHOOTING

PROBLEM

LEDS

No sound or very

Power LED

low sound level.

turned off.

Transmitter LCD turned off.

Receiver RF indicator is off.

Receiver turned on

and RF light on.

Distortions or unwanted

Receiver RF

interferences.

antenna lit.

Receiver LOW

BATT LED

flashes.

Distorted sound.

Too high level

indicator of the

transmitter.

Transmitter is

Listening to a Mono signal only

in Stereo

from one hearphones side.

mode.

Mode Stereo and MIX activated:

you want to hear only the right

input signal transmitter, even if

Transmitter is

the transmitter is in Stereo mode

in Mono mode.

and both the transmitter inputs

are used. (ING 30 only).

Listening to two independent

mono signals in left and right

earphones, but you want to hear

the signals in both earphones

(ING 30 only).

SOLuTION

Make sure the batteries are not discharged

and that the receiver is turned on.

Check the connection between power

supply and the transmitter.

Turn on the transmitter.

Make sure that transmitter and receiver are

set to the same frequency.

Reduce the distance between transmitter

and receiver, and verify that the two devices

are in direct visual contact.

Make sure that the transmitter antenna is

mounted correctly.

Raise the volume of the receiver and check

earphones connection.

Check the input level of the transmitter and,

possibly, increase it.

Increase the distance from possible causes

of interference (digital control devices, such

as CD player, console ...).

Use a different frequency.

Replace the batteries.

Turn down the volume control of the

transmitter or the volume of the source

device.

Set the transmitter in Mono mode.

Set the transmitter in Stereo mode.

Activate MIX in the transmitter.

ING Series

| User manual