DS Produkte 06839 Instructions Manual - Page 3
Browse online or download pdf Instructions Manual for Lighting Equipment DS Produkte 06839. DS Produkte 06839 6 pages.
EN
Items Supplied and Article Overview
11
10
9
8
7
Unpack the article and remove all protective fi lms and stickers
that may be present. Check the items supplied for completeness
and possible transport damage. If you fi nd any transport damage,
contact the customer service department immediately.
Assembly
CAUTION!
■
Before drilling the holes for the wall mounting, ensure that there
are no cables or pipes in the wall that could be damaged.
1. Select a position for the solar spotlight where the solar panel
can absorb direct sunlight for the whole day as far as possible
(preferably south-facing) and where no obstacles such as
parked cars, fences or trees can restrict the sensor area.
2a. If you want to anchor the solar
2b. If you want to screw the solar
•
•
•
•
Push the stem of the solar spotlight onto the base and fi x
the parts together with the fi xing screw.
3. Adjust the angle of the spotlight and then tighten the hinge
screw.
The solar panel can only be turned slightly to the left and
right. It is not possible to turn it 360° and it cannot be tilted
up or down.
4. Peel the protective fi lm off the solar panel and turn it to face
the sun.
5. Activate the solar spotlight by pushing the slide switch on the
bottom.
DS Produkte GmbH, Am Heisterbusch 1, 19258 Gallin, Germany •
1 Solar panel
1
2 Housing
3 Frame
4 Hinge screw
2
5 Fixing screw
6 Base
7 Stem
3
8 Switch
4
9 Red
LED
(simulates
surveillance camera)
5
10 Motion sensor
11 LED ring
6
Not shown:
•
Ground spike
•
Fastening material
spotlight in the ground, take the
ground spike, plug its blunt end
into the stem of the solar spotlight
and fi x both parts together with the
fi xing screw which is supplied. Push
the ground spike into the ground.
spotlight to the wall or on a horizontal
surface, use the base.
Place the base on the chosen
surface, mark four drill holes and
then drill the holes.
Push the dowels which are supplied
into the holes.
Screw the base so that it is securely
attached using the screws which are
supplied.
Customer Service / Importer:
*) Calls subject to a charge. Costs vary depending on the provider.
Instructions
The solar spotlight contains four batteries. When it is fi rst
used, it takes approx. 8 hours with sunlight shining directly
on the solar panel for the batteries to be fully charged up.
As soon as the batteries are charged up, the red LED starts
fl ashing and simulates a surveillance camera.
When it gets dark, the motion sensor is activated
automatically. If the sensor detects a moving object within
a radius of 3 to 4 metres, the spotlight lights up for approx.
30 seconds and then automatically switches itself off again.
When it gets light, the motion sensor switches off and the
batteries are charged up via the solar panel.
Cleaning and Storage
CAUTION!
■
Do not use any corrosive or abrasive cleaning agents to clean
the article.
•
From time to time, clean the solar panel and the spotlight with a
damp cloth. Dirt and dust stop the article from working properly.
•
If you do not want to use the article for a lengthy period of time,
take the batteries out. Store the article in a dry place.
Changing the Battery
CAUTION!
■
Before inserting a new battery, check whether the contacts in
the article and on the battery are clean, and clean them if ne-
cessary.
■
Use only the battery type specifi ed in the technical data (see
the "Technical Data" chapter).
If the performance of the spotlight diminishes, the battery should
be replaced. You require 1 x 3.2 V Accu LiFEPO4, AA type.
1. Remove the spotlight from the base or ground spike.
2. Turn the frame anticlockwise and remove it from the housing.
3. Carefully pull the LED ring out of the housing. Make sure that
the cable connections are not damaged!
4. Undo the cable tie and remove the battery.
5. Insert a new battery. Pay attention to the correct polarity (+ / –).
6. Slide the cable tie over the battery and carefully insert the LED
ring back into the housing.
7. Screw the frame back onto the housing.
Disposal
The packaging material is recyclable. Dispose of the pack-
aging in an environmentally-friendly manner and make it
available to the collection service for recyclable materials.
Dispose of the product in an environmentally-friendly
manner. The product does not belong in the household
garbage. Dispose of it at a recycling centre for old electric
and electronic equipment. For more information, please
contact the administration in your community.
Batteries and storage batteries must be removed and
disposed of separately before disposing of the product.
To protect the environment, batteries and rechargeable
batteries may not be disposed of together with normal
household waste. Instead they must be turned in at
appropriate
applicable statutory provisions regulating the disposal of
batteries.
All rights reserved.
3
Article number: 06839
collection
points.
Please
✆
+49 38851 314650 *)
also
observe