Aube Technologies TH132 A Owner's Manual - Page 3

Browse online or download pdf Owner's Manual for Control Unit Aube Technologies TH132 A. Aube Technologies TH132 A 3 pages. Control module
Also for Aube Technologies TH132 A: Owner's Manual (3 pages)

Print Page

The PB130-230 power base is designed to power a TH13x

Series control module. The resistive load must not exceed

3680 watts (NI) @ 230 VAC (16 A).

Turn off power to the heating system at the main power panel

to avoid electrical shock. Installation should be carried out by

an electrician.

All work must conform to the applicable country standards for

electrical installations and wiring.

This thermostat should be connected on a circuit equipped

with a fuse or a circuit breaker. It must be installed on a certi-

fied electrical box.

For a new installation, choose a location about 1.5 m above

the floor.

For electric baseboards, convectors and fan-forced heaters,

the thermostat must be installed facing the heating system.

The thermostat must be installed on an inside wall.

Avoid locations where there are air drafts (top of staircase, air

outlet), dead air spots (behind a door), direct sunlight or con-

cealed chimneys or stove pipes.

One (1) PB130-230 power base

One (1) floor sensor (for AF and F control modules only)

One (1) wall plate (optional, in certain countries)

Model: PB130-230

Supply: 230 VAC, 50 Hz

Load: 16 A maximum (resistive only)

Power: 3680 Watts (NI) @ 230 VAC

Approval: EN60730-2-9 / EN50081-1 / EN50082-2

Storage: -20°C to 50°C

Protection: Class 2

Protection

degree: IP20

Automatic

action: Type 1.B

Environment: Normally polluted

Size (H • W • D)

: 2.95 x 2.95 x 0.55 in. (75 x 75 x 14 mm)

NOTE:

The terminals are designed to handle a cross-section of

wire measuring 0.33 to 3.1 mm

If you have any questions concerning the installation of the

PB130-230 power base, contact our technical support team at:

705 Montrichard

Saint-Jean-sur-Richelieu

Quebec, Canada J2X 5K8

Tel.: (450) 358-4600

Toll Free: 1-800-831-AUBE

Fax: (450) 358-4650

Email: [email protected]

For more information on our products, visit us at

www.aubetech.com

10 rue Ampère

95500 Gonesse

France

33 (0) 1 34 07 99 00

33 (0) 1 34 07 99 19

[email protected]

Remove the screw holding the

control module to the power base

and lift the lower part upwards.

The screw cannot be completely

removed.

If you have a wall

plate: Before making

the connections, make sure that the base

covers the electrical box entirely. If not,

insert the wall plate on rear of the base.

NOTE:

The wall plate can be used for aesthetic

purposes only.

Connect the wires:

•

Power (L,

N):

Terminals 1 and 5

•

Load (L,

N):

Terminals 2 and

see notes 1 & 2

•

Pilot Wire

(F.P.):

Terminal 3

see note 3

•

Floor

sensor:

Terminals 6 and 7

(no polarity needs

to be respected)

Note 1

If the load is driven through a contactor, it is recommended

to install a snubber at the contactor's coil terminal to

extend the contactor's life expectancy and ensure a good

operation of the thermostat.

Note 2

Compatible with TH131 control module only.

Note 3

The floor sensor wire cannot lay across or next to any

heater wires. For maximum performance, the sensor must

be centered between the wires at a maxi-

mum temperature of 80°C.

Push wires into the electrical box and

secure the base to the electrical box

anchorage. The head of the screw

must be less than 2 mm thick.

BEFORE mounting the control

module onto the base, configure the

switches (if any) and install the con-

trol module onto the base

user

guide).

Return power to the heating system.

WARNING: this power base must be used

heating cycles (temperature control). Depending on the selected

control module, make sure that the switch is set at

AUBE TECHNOLOGIES INC. TWO (2) YEAR LIMITED WARRANTY

This product is guaranteed against workmanship defects for a two-year period following

the initial date of purchase. During this period, AUBE Technologies Inc. will repair or

replace, at our option and without charge, any defective product which has been used

under normal conditions.

The warranty does not cover delivery costs and does not apply to products poorly

installed or randomly damaged following installation. This warranty cancels and

replaces any other manufacturer's express or implied warranty as well as any other

company commitment.

AUBE Technologies Inc. cannot be held liable for related or random damages following

the installation of this product. The defective product as well as the purchase invoice

must be returned to the place of purchase or mailed, prepaid and insured, to the

nearest location.

(refer to the

only

with

15-minute

minutes.

19/01/2004

400-130-001-B